Basic Level     Skills: Not specified    
Author
Author email
[email protected]
Author website
www.binu.somee.com

Description

The Project Long Range Remote Control can be used to remotely control a number of Electrical or Electronic Gadgets connected to it. Unlike Infra Red remote control, this Project employs FM transmission and Reception, and hence it can be used for comparatively longer range. Any gadget can be switched on/off by keying the number allocated to it. The Receiver is made up of the famous 8 bit Microcontroller from Atmel. The Microcontroller is used as the Master in the receiver end which is used to control all the devices. It decodes the Signal from the transmitter and control the relays according to the signal. For transmission we are using frequency modulation at the frequency of 433.92Mhz.
  Filesize

88.75 kB

  Downloads

47676

  Rating
 

Comments

(Required; Min length 5)
(Required; will not be displayed)

Conversation

ajay_bhargav
Sat Aug 30 2014, 12:15 PM
@sufiyan, You can use solenoid lock in place of LED.
Fri Aug 29 2014, 12:17 AM
sufiyan
please can you tell me which type of lock activator should i connect in place of LED? can i use selenoid lock actuator
ajay_bhargav
Thu Aug 28 2014, 06:34 AM
Please post questions in forum
Thu Aug 28 2014, 01:44 AM
yednekachew
can you give a project made bay proteus software
Mon Aug 25 2014, 07:12 AM
Vinod Soni
Hi Sir, How can i make this RFID with ATMega16/32 controller
pavanjain
Sat Aug 23 2014, 05:10 AM
Sir i want to download the hex file in P89v51rd2 microcontroller using max232 IC but we not load the program in IC
Tue Aug 19 2014, 04:51 PM
allen ndumu
please i will like to know if the problem of speed control of dc motor using keypad and l298 was if yes can i have the complete project send it to the address i really need to see it
Tue Aug 19 2014, 10:47 AM
Amit Bisht
sir i want to have some trending projects on which i could work related to ATmega 16 microcontroller
ExperimenterUK
Sat Aug 16 2014, 04:16 PM
@diligent . create a thread
Sat Aug 16 2014, 03:17 PM
diligent
in assembly langauage programming..

Downloads

Comments

enisi
Wed Aug 27 2014, 06:08 AM
sadalakshmi
Wed Aug 27 2014, 12:39 AM
Paecake
Sun Aug 24 2014, 04:07 PM
pavanjain
Sat Aug 23 2014, 02:33 AM
samchovatiya
Thu Aug 21 2014, 02:30 PM
hasmukhjain
Wed Aug 20 2014, 06:28 AM
rablo
Tue Aug 19 2014, 10:10 AM
faizhameed
Tue Aug 12 2014, 10:39 PM

Online

Guests: 41, Members: 0 ...

most ever online: 182184
(Members: , Guests: 182184) on 06 Aug 2010: 01:37 AM

Members: 37501
Newest member: enisi
Forum Activity
ajay_bhargav Avatar
Posted By ajay_bhargav
Sat Aug 30 2014, 12:03 PM
Forgot to attach files. This has source for both R...
ajay_bhargav Avatar
Posted By ajay_bhargav
Sat Aug 30 2014, 11:56 AM
I found a very good working source but its for PIC...
siddique Avatar
Posted By siddique
Sat Aug 30 2014, 03:34 AM
Have you tried using the TX setup to receive and v...
ExperimenterUK Avatar
Posted By ExperimenterUK
Thu Aug 28 2014, 03:31 PM
So, I don't think there is any need to load any da...
ajay_bhargav Avatar
Posted By ajay_bhargav
Thu Aug 28 2014, 06:33 AM
Did your professor ask this question to you? I sug...
siddique Avatar
Posted By siddique
Thu Aug 28 2014, 01:09 AM
hi,In the Tx code, I have disabled auto acknowledg...
ExperimenterUK Avatar
Posted By ExperimenterUK
Wed Aug 27 2014, 04:59 PM
Your board has two serial ports, are you connectin...
ExperimenterUK Avatar
Posted By ExperimenterUK
Wed Aug 27 2014, 04:45 PM
In your TX code I see where you set payload width ...
enisi Avatar
Posted By enisi
Wed Aug 27 2014, 07:05 AM
It can be more than one ansawer correctly
enisi Avatar
Posted By enisi
Wed Aug 27 2014, 06:57 AM
Port 0 is connected indicator 7 segments, so that ...