Basic Level     Skills: Not specified    
Author
Author email
[email protected]
Author website
www.binu.somee.com

Description

Project not tested


Short Message Service (SMS) is defined as a text-based service that enables up to 160 characters to be sent from one mobile phone to another. In a similar vein to email, messages are stored and forwarded at an SMS centre, allowing messages to be retrieved later if you are not immediately available to receive them. Unlike voice calls, SMS messages travel over the mobile network’s low-speed control channel. Using the convenience of SMS, this project lets you remotely control equipment by sending plain text messages, such as "pump on", "aircon off", "reset" or "light1 on" – all of which can be pre-programmed into the controller and easily remembered later. It can control up to eight external devices. The 8 bit microcontroller is used to control the whole circuit. It read message from the Mobile phone and control the devices according the received message.

NOTE:
This project does not have C code. you can download it for your reference.

For more information you can contact the author.
  Filesize

63.59 kB

  Downloads

97201

  Rating
 

Comments

(Required; Min length 5)
(Required; will not be displayed)

Conversation

ExperimenterUK
Tue Jul 19 2016, 05:59 PM
@mhammad 64 bits is 8 bytes.
Tue Jul 19 2016, 07:56 AM
mhammad kassem
hello! i want to know how to use UART in mikroc , I want to receive 64 bits from another microcontroller and i dont know how to start my code to receive the 64 bits...any help?
ExperimenterUK
Mon Jul 18 2016, 08:32 PM
@meena.. are you still having trouble ?
Sat Jul 16 2016, 10:19 AM
Meena
problem in loading email address while registering.Please help
Sun Jul 10 2016, 02:50 PM
shockwave
could you please provide a sample code that controling LED using bluetooth HC-05 interfacing pic16f877a thank you!
Sun Jul 10 2016, 02:49 PM
shockwave
Help!
ExperimenterUK
Sat Jul 09 2016, 05:25 PM
@Santhana krishnan post in forum to discuss your problem
Thu Jul 07 2016, 09:26 AM
Santhana krishnan
Hi i program atmega 32 it was functiining corectly but now aref pins voltage 2.56 is droped to .85 volts also a ports input viltage also dropped so anologe inpit not funcitonig please help me to find out the problem
Thu Jul 07 2016, 09:24 AM
Santhana krishnan
Hi i program the atmega 32
Thu Jul 07 2016, 09:24 AM
Santhana krishnan
Hi

Downloads

Comments

adithyapaip
Thu Jul 21 2016, 05:45 PM
celu
Thu Jul 21 2016, 05:27 PM
Aiko
Wed Jul 20 2016, 01:51 PM
JorgeG
Sat Jul 16 2016, 07:19 PM
Piotrekk
Wed Jul 06 2016, 09:35 AM
dyoussef
Wed Jun 29 2016, 07:29 PM
sung7333
Tue Jun 28 2016, 06:23 AM
Bonolai
Fri Jun 24 2016, 06:02 AM

Online

Guests: 31, Members: 0 ...

most ever online: 182184
(Members: , Guests: 182184) on 06 Aug 2010: 05:37 AM

Members: 37775
Newest member: adithyapaip
Forum Activity
ExperimenterUK Avatar
Posted By ExperimenterUK
Sat Jul 23 2016, 07:14 PM
I found this datasheet, it is a type of driver.It ...
Piotrekk Avatar
Posted By Piotrekk
Fri Jul 22 2016, 10:12 AM
I found an old box of electronic components in the...
ExperimenterUK Avatar
Posted By ExperimenterUK
Thu Jul 21 2016, 07:37 PM
That is curious, but very likely a co-incidence.Th...
adithyapaip Avatar
Posted By adithyapaip
Thu Jul 21 2016, 07:18 PM
I am using keil to do everthing in 8051,when I was...
ExperimenterUK Avatar
Posted By ExperimenterUK
Thu Jul 21 2016, 07:14 PM
By far the easiest and cheapest way to talk to the...
ExperimenterUK Avatar
Posted By ExperimenterUK
Thu Jul 21 2016, 07:04 PM
The crystal on the programmer does not affect the ...
adithyapaip Avatar
Posted By adithyapaip
Thu Jul 21 2016, 06:06 PM
Hi Guys..i have a 8051 programmer which has 4mhz c...
Aiko Avatar
Posted By Aiko
Wed Jul 20 2016, 01:56 PM
ankitbajaj01 Avatar
Posted By ankitbajaj01
Wed Jul 20 2016, 04:49 AM
Dear All,Greetings!!!I want to develop Online moni...
sairfan1 Avatar
Posted By sairfan1
Tue Jul 19 2016, 09:56 PM
Now a days there are many smart locks available li...