Basic Level     Skills: Not specified    
Author
Author email
[email protected]

Description

Automatic Room light Controller with Visitor Counter


Project not tested

This Project "Automatic Room Light Controller with Visitor Counter using Microcontroller" is a reliable circuit that takes over the task of controlling the room lights as well us counting number of persons/visitors in the room very accurately. When somebody enters into the room then the counter is incremented by one and the light in the room will be switched ON and when any one leaves the room then the counter is decremented by one. The light will be only switched OFF until all the persons in the room go out. The total number of persons inside the room is also displayed on the seven segment displays.

The microcontroller does the above job. It receives the signals from the sensors, and this signal is operated under the control of software which is stored in ROM. Microcontroller continuously monitor the IR Sensors, When any object pass through the 555 timer generates a pulse and interrupt controller. So visitors in the room are counted up by Sensor1 and Sensor2 counts visitors going out of room. As soon as visitor count reaches 0 the room light turns off.

We already had this project in our download section but Anudeep (bobdxcool) had made it working. Thank you so much for sharing this project back.

Here is a working video of project shared by Anudeep:





  Filesize

73.39 kB

  Downloads

147509

  Rating
 

Comments

lance
29 Aug 2014: 15:18 PM
ahmm what software should i use to program the microcontroller ? i am very glad if you will help me with this project .. thank you very much
  
ajay_bhargav
30 Aug 2014: 16:17 PM
You will need a programmer hardware, If your controller software support ISP then you can use simple ISP programmer which has little hardware. If you need more help I would suggest posting in fourm.
  
mahi000
22 Nov 2014: 15:34 PM
Its urgent plzz reply Asap!
I hv implemented this project using the same schematic and hex file from the zipped folder,'ROOM' : room.hex bt its not wrkng properly!
the seven segment isnt displayng the count 00 even in the start! and nthng is happening after passing obstruction thru the sensors :/
plzz hlp!!
need a working assembly lang code for keil!
and also a hex file t wd wrk !
hvto sbmt in 2 days
  
ajay_bhargav
26 Nov 2014: 04:53 AM

hvto sbmt in 2 days

mahi000


You have to start your project well in time. Debugging hardware always need time. Please post in forum for help. This is not the right place.
  
Niharika
01 Jan 2015: 16:56 PM
I need an arduino program for automatic room light on off controller with counter.
Would you please provide me ?
  
sandykura
07 Jan 2015: 19:29 PM
Hello sir,
I am trying to implement this project but j'm having some trouble with the code, is there any way i can contact you to ask some questions?
  
ajay_bhargav
09 Jan 2015: 05:06 AM
@sandykura Feel free to post your questions and doubts in our forum Or you can simply click on "post a question" button.
  
jaysukh
15 Apr 2015: 18:31 PM
i need source code of IC AT89s52.please provide me
  
ajay_bhargav
17 Apr 2015: 12:51 PM
@jaysukh, Please download it using the green color download file button.
  
somia
19 Jun 2015: 05:29 AM
sir i need the coding of room light control using visitor counter.......it's urgent...it's for my traning project
  
ajay_bhargav
23 Jun 2015: 13:30 PM
@somia, Project is free to download...
  
Divyansh
26 Aug 2015: 14:13 PM
I need help in making a 8051 project. Can anyone help.
  
ajay_bhargav
27 Aug 2015: 07:38 AM
@Divyansh, post in forum please
  
yashb5
31 Oct 2015: 13:39 PM
i made the project, but after something cuts through ir led and sensor,the input at P1.0 or P1.1 in microcontroller takes about 4-5 sec to go back to 0.

  
yashb5
31 Oct 2015: 13:41 PM
and what can be the maximum distance between ir led and tsop sensor
  
nirmal kumar
04 Jan 2016: 05:15 AM
What if there r 3 fan , 3 lights in a room and i need only light and a fan tp be turned on! Will the project fail there?
  
YashSinghal
04 Apr 2016: 14:34 PM
Can anyone explain the hex2bcd subroutine used in this program... Its urgent....
  
lokanath
23 May 2016: 17:33 PM
sir i was downloaded the file in that file i didn't get the source code . program? ,.i need program
  
Ahmed seid
07 Nov 2016: 07:23 AM
I need an arduino program for automatic room light on off controller with counter.
Would you please provide me ?
  
(Required; Min length 5)
(Required; will not be displayed)

Conversation

ExperimenterUK
Sat Oct 12 2019, 10:23 PM
Log in.. then post your code in the 8051 forum
Sat Oct 12 2019, 10:18 AM
Bhadra Sajikumar
i am doing a countdown timer with 8051 for my project, unfortunately our professor had to take a leave of absence before he could teach us most of it.. can someone explain the .asm code of it for me?
Mon Sep 23 2019, 07:37 AM
Nathaniel
I am doing a project for my schools wireless security system with cameras,sensors and spot lights using 8051 micro controller, could you help me out with the design and its source code.
Wed Sep 18 2019, 08:48 PM
Caryn Kover
Thank you for your time,
ExperimenterUK
Mon Aug 05 2019, 07:09 PM
@Ismail ..post in forum, give details
Mon Aug 05 2019, 04:33 PM
Ismail balghmi
Hello. Please I won't download
ExperimenterUK
Wed Jul 24 2019, 12:47 AM
@BUSTER123 Please post in the forum
Tue Jul 23 2019, 06:13 PM
BUSTER123
hello! newbie here. i am kind of a guy who hates using ready - made existing libraries, so this helped a lot as i was trying to control and write to a character lcd display. however, i can't figure out how to set the cursor position. for example, i want to set it to the 5th column in the first row, so position 5. so according to the table, i am sending 10000101 on the 8 data lines of the lcd (register select pulled low). the cursor does not move there however. and i cant move the cursor left or right too. is it something wrong that i am doing? thank you.
ExperimenterUK
Thu Jul 11 2019, 07:55 PM
@ramos https://www.theengineeringprojects.com/2017/09/l298-motor-driver-library-proteus.html
ExperimenterUK
Thu Jul 11 2019, 07:44 PM
@praveen123. Can you give a link to the project ?

Downloads

Comments

DeepakBGattani
Mon Nov 11 2019, 01:31 PM
Jeanbusatta
Sun Nov 10 2019, 04:42 AM
mdayaz
Sat Nov 09 2019, 03:41 PM
baoyen123
Fri Nov 08 2019, 10:06 AM
xiwang
Fri Nov 08 2019, 07:28 AM
ilylily07
Tue Oct 15 2019, 04:32 PM
hientran123
Tue Oct 15 2019, 02:27 AM
Sat Oct 05 2019, 02:38 PM

Online

Guests: 107, Members: 0 ...

most ever online: 182184
(Members: , Guests: 182184) on 06 Aug 2010: 05:37 AM

Members: 38102
Newest member: DeepakBGattani
Forum Activity
Jeanbusatta Avatar
Posted By Jeanbusatta
Sun Nov 10 2019, 04:43 AM
ty, really needed it
ExperimenterUK Avatar
Posted By ExperimenterUK
Tue Oct 22 2019, 05:18 AM
wimac Avatar
Posted By wimac
Mon Oct 21 2019, 09:18 AM
I’ve been following this thread and looking at the...
s_dinesh40@yahoo.com Avatar
Posted By [email protected]
Sun Oct 20 2019, 03:09 PM
s_dinesh40@yahoo.com Avatar
Posted By [email protected]
Sun Oct 20 2019, 03:02 PM
sir, when i on display ,sometime 3rd display is no...
s_dinesh40@yahoo.com Avatar
Posted By [email protected]
Sun Oct 20 2019, 02:53 PM
sir, when i on display ,sometime 3rd display is no...
ExperimenterUK Avatar
Posted By ExperimenterUK
Sun Oct 20 2019, 12:21 AM
Your code seems okay on my simulationTry my code o...
s_dinesh40@yahoo.com Avatar
Posted By [email protected]
Sat Oct 19 2019, 07:13 PM
please find video attachment. 3rd & 4th displa...
s_dinesh40@yahoo.com Avatar
Posted By [email protected]
Sat Oct 19 2019, 07:05 PM
sir, 3rd and 4th dot matrix display flickering, ...
ExperimenterUK Avatar
Posted By ExperimenterUK
Fri Oct 18 2019, 09:18 PM
Hopefully you understand some of the program.Which...