Discussion in "Project Help" started by    isha    Jul 11, 2007.
Wed Jul 11 2007, 06:59 pm
#1
sir, i've a question related to the project named 'Digital Visitor Counter', that ''what type of sensors are used in this project" , complete information about these sensors..... reply me as soon as possible
Thanks
Tags Digital Visitor Countersensors for Visitor counter
Wed Jul 11 2007, 07:16 pm
#2
Thank you for posting it here.. this is going to help others too
...
so, regarding the sensors, in the project, LDRs are used. LDR = Light Dependent Resistor
There are two LDRs in the circuit, one is on the exit door and on the entrance door.
So when someone crosses the entrance door, it counts the visitor up and when someone crosses the exit door, it decrement the counter.
Timer is setup to refresh the 7-Segment display.
Hope this information is sufficient for the project. If anymore info is needed feel free to ask
 Halley like this.
Tags Digital Visitor Countersensors for Visitor counter
Sun Dec 21 2008, 04:56 pm
#3
The visitor counter isnt working, some problem in the cde.... the rxd port is not read....
Help!!!
Sun Dec 21 2008, 04:59 pm
#4
I want to shift the inputs to some other port so I can serial port it....
But the circuit code only increments and doesnt decrement....
Sun Dec 21 2008, 05:03 pm
#5
whats the exact problem? are you sure your hardware is ok?
Sun Dec 21 2008, 05:13 pm
#6
i simulated the code on software to make sure its working before i shifted to hardware, and it only increments and doesnt decrement.... sensor circuits work on software... i tried it on hardware and I cant get my sensors to work, but im going to get something of better quality...
the problem seems to be in the rxd port... its not read...


[ Edited Sun Dec 21 2008, 05:24 pm ]
Sun Dec 21 2008, 06:03 pm
#7
how did you make sensor circuit? using switches? which software are u using for simulation? send me hex + ckt if proteus.
Sun Dec 21 2008, 06:29 pm
#8
Your post is not clear.
You're saying it works ok in simulation but not in hardware?
Or it doesn't work in either?

You must remember....for incrementing,the sensor at P3.0 must be obsteucted first and then P3.1
For decrementing,P3.1 must be obstructed first and then P3.0
Fri Jul 17 2009, 07:27 am
#9
sir in this circuit .how relay will be connected..it is of five pin..but in circuit it is not clear how to connect,..plz help
Sun Jul 19 2009, 11:50 pm
#10


sir in this circuit .how relay will be connected..it is of five pin..but in circuit it is not clear how to connect,..plz help

sharik



i saw the circuit and its all clear, your coil is connected with one pin to VCC and other to Q1 transistor.

NO(normally open) is connected to bulb and NC(normally closed) is not connected.

common pin is connected to AC supply.

what is not clear to you, please mention.

One suggestion is to open up a new thread for yourself instead of posting in a thread which is months old

Get Social

Information

Powered by e107 Forum System

Downloads

Comments

Bobbyerilar
Thu Mar 28 2024, 08:08 am
pb58
Thu Mar 28 2024, 05:54 am
Clarazkafup
Thu Mar 28 2024, 02:24 am
Walterkic
Thu Mar 28 2024, 01:19 am
Davidusawn
Wed Mar 27 2024, 08:30 pm
Richardsop
Tue Mar 26 2024, 10:33 pm
Stevencog
Tue Mar 26 2024, 04:26 pm
Bernardwarge
Tue Mar 26 2024, 11:15 am