pic programmer circuit
Discussion in "PIC Microcontroller Discussion" started by yashshailesh Sep 29, 2010.
Sat Dec 04 2010, 11:07 pm
Hi Yash,
Majoka has posted 2-3 circuits of programmer. which one you've built? and what programmer software are you using for them?
also the olimex programmer circuit is simplest
you can make a six pin header and connect device to it. check olimex website for frontend software too.
Majoka has posted 2-3 circuits of programmer. which one you've built? and what programmer software are you using for them?
also the olimex programmer circuit is simplest
you can make a six pin header and connect device to it. check olimex website for frontend software too.
yashshailesh like this.
Tue Dec 07 2010, 10:09 am
hello sir sorry for late ,
i use pcb which is in pcb folder .i hv attached in earlier post. i made hardware . sir i hv used icprog1v06. when i m burning program there is no indication (acknowledgement). plz sir help me wt i m ding wrong. i m waiting yr response.
i use pcb which is in pcb folder .i hv attached in earlier post. i made hardware . sir i hv used icprog1v06. when i m burning program there is no indication (acknowledgement). plz sir help me wt i m ding wrong. i m waiting yr response.
Wed Dec 08 2010, 12:18 am
hi yashshailesh
i make it also on pcb and it work in first attempt
check ur connections once again
specially check transistors
all detail is given here
http://feng3.cool.ne.jp/en/pg5v2.html
in documentation 2 things are clearly mentions
other important points r also available on above link
i make it also on pcb and it work in first attempt
check ur connections once again
specially check transistors
all detail is given here
http://feng3.cool.ne.jp/en/pg5v2.html
in documentation 2 things are clearly mentions
1) I recommend checking to see if there is enough output voltage at the serial port your personal computer. If TxD, DTR, and RTS do not have more than +7.5V(or -7.5V), this programmer will not work well, especially, with the latest laptop computers that using low power RS232 interface ICs.
2) The GND line of a serial port forms relative VDD on a PIC programmer. All the GND symbols in a circuit diagram are a PIC programmer's GND. Never connect them with GND line of a serial port.
other important points r also available on above link
yashshailesh like this.
Tue Dec 14 2010, 10:36 am
hello majoka & ajay sir,
thanks for yr kind support , sir my programmer is working. hello ajay sir as u came in this thread, it started working .
wt u r doing help for we such type of student is undefinable sir .thanks to both of u & 2 all.
thanks for yr kind support , sir my programmer is working. hello ajay sir as u came in this thread, it started working .
wt u r doing help for we such type of student is undefinable sir .thanks to both of u & 2 all.
Sat Dec 18 2010, 04:07 pm
hello sir ,
i want to ask,
(1) i hv 2 type of crystal 12MHz & 24MHz. i m using Pic 16f877a. which one is suitable .
(2). what will be capacitor combination with that.
i want to ask,
(1) i hv 2 type of crystal 12MHz & 24MHz. i m using Pic 16f877a. which one is suitable .
(2). what will be capacitor combination with that.
Sat Dec 18 2010, 09:33 pm
hi yashshailesh
it depend on ur application u want to do
normal pic has maximum 20 MHz operating range so use 12 MHz
use 22pf cap
it depend on ur application u want to do
normal pic has maximum 20 MHz operating range so use 12 MHz
use 22pf cap
Mon Dec 20 2010, 10:15 am
Thanku sir,
Sir ; is d above programmer ckt (Ajay sir) supports "PIC18F90J60 " with winpic800?.
Sir ; is d above programmer ckt (Ajay sir) supports "PIC18F90J60 " with winpic800?.
Mon Dec 20 2010, 10:21 am
hi yashshailesh
see its documentation
it support most of the ic that software has
u can use winpicpgm software also it is best where if fails there i use winpic800
it never fail to program
that ics listed in software that r supported by hardware
some ics are special that's pin are not compatible with hardware
so use an extra board to program that
see its documentation
it support most of the ic that software has
u can use winpicpgm software also it is best where if fails there i use winpic800
it never fail to program
that ics listed in software that r supported by hardware
some ics are special that's pin are not compatible with hardware
so use an extra board to program that
Wed Dec 22 2010, 01:01 pm
Thank u for ur kind information
------------------------------------------------------
plc training in chennai
seo company chennai
plc training in chennai
------------------------------------------------------
plc training in chennai
seo company chennai
plc training in chennai
Powered by e107 Forum System