Voice Recognization Chip AP7003-02 : 8051 Microcontroller Projects AVR PIC Projects Tutorials Ebooks Libraries codes

Forums

8051 Microcontroller Projects AVR PIC Projects Tutorials Ebooks Libraries codes :: Forums :: Project Development :: Project Doubts		<< Previous thread \| Next thread >>
Voice Recognization Chip AP7003-02

Go to page [1] 2
Moderators: Ajay, Junied , abbas1707, Arun Kumar V, pdi33, Shailesh NAYAK, ۞ TPS ۞, shyam, sashijoseph

Author

Post

SANATH EMBEDDED

Mon May 05 2008, 04:26PM

Registered Member #2561

Joined: Tue Jul 24 2007, 11:26PM

Posts: 132
Thanked 14 times in 12 posts

Hi to all,
I am currently working on the project " Voice activated intelligence robotic system" for which i am making use of AP7003-02 Chip. I have rigged up the circuit what has been given in the datasheets. But in the datasheets the details for the traininng mode and recognization mode has not been given properly.
So in the datasheets it is given that
Step1: The 12 word memory banks must be cleared after power on and before store word.At the begin of store word mode LED1 and one of the PortA ( 1~12) whcih is corresponed to selected word bank is active. and AP7003-02 will go to recognization mode after input voice is stored into word bank.( So for that I am making use of push-button switch provided to the PIT4 pin. After I press the LED1 starts blinking and after some seconds LED2 gets ON.How can I store the word in to memory bank .)
Can anyone kindly help me this matter.

Here I enclosed the rapid-share link for the datasheets and the schematics.

http://rapidshare.com/files/112896302/AP7003_Voice_Recognization_chip.rar

Regards
Sanath
Bangalore

With Regards,

Sanath Kumar
Mangalore/ Bangalore/Pune

Email: sanathmcx@rediffmail.com

" Embedded System is my Passion "

Shailesh NAYAK

Tue May 06 2008, 02:51PM

Registered Member #2498

Joined: Mon Jul 23 2007, 01:20AM

Posts: 39
Thanked 9 times in 7 posts

Hi,
I am not much familiar with programable audio recording IC's but in Mumbai APLUS IDIA can help you out on it. http://aplusindia.net/aplusindiauser/AddCategoryMasterAction.apu

Best Regards

Shailesh S. NAYAK

SANATH EMBEDDED

Tue May 06 2008, 02:55PM

Registered Member #2561

Joined: Tue Jul 24 2007, 11:26PM

Posts: 132
Thanked 14 times in 12 posts

Can anyone tell me the Memory Bank what this Chip is having volatile or Non-volatile memory since in the datasheet it is not mentioned.

Regards
Sanath

With Regards,

Sanath Kumar
Mangalore/ Bangalore/Pune

Email: sanathmcx@rediffmail.com

" Embedded System is my Passion "

Ajay

Tue May 06 2008, 03:16PM

Rickey's World Admin

Registered Member #1

Joined: Fri Feb 24 2006, 04:56AM

Posts: 3745
Thanked 695 times in 654 posts

you just need to send command where you want to store your word.
See table 1 for timing information and page 8 for functional description.

In the datasheet there is no information given regarding clock and other things. how it is to be connected and how micro can read data.
I think you reconsider what shailesh said and contact the vendor for more information. You have bought IC from them so you must get full support.

www.rickeyworld.info
If you feel satisfied with the user's forum reply please click on the thank button.

Obey forum rules!
Respect others!

sashijoseph

Wed May 07 2008, 02:54PM

Registered Member #5870

Joined: Mon Feb 04 2008, 06:26PM

Posts: 552
Thanked 124 times in 117 posts

SANATH MCX wrote ...

Step1: The 12 word memory banks must be cleared after power on and before store word.At the begin of store word mode LED1 and one of the PortA ( 1~12) whcih is corresponed to selected word bank is active. and AP7003-02 will go to recognization mode after input voice is stored into word bank.( So for that I am making use of push-button switch provided to the PIT4 pin. After I press the LED1 starts blinking and after some seconds LED2 gets ON.How can I store the word in to memory bank .)
Can anyone kindly help me this matter.

Hi...try following this sequence...
- Power On
- Press PIT4 switch
- Press '1' in keypad
- Speak into the mic to record into bank1(LED1 should be active during this period)
- Then press '2' for selecting bank2 and when LED1 is active speak into the mic to record.
Similarly proceed with other words.
Then press '9' or '10' to select threshold level and go into recognition mode.
In recognition mode LED1 will be active again waiting for an input word in the mic.
Then if the input word matches any stored word,LED2 and the corresponding port pin will become active.Else LED1 will flash to indicate no match and then again revert to recognition mode.
If a match was found and LED2 had become active,it will remain in tht state for 3 minutes and ten revert to recognition mode.If you want the recognition cycle before the 3 min. are over you may press '11'.
Do give a try and report.

Let there be music........

SANATH EMBEDDED

Wed May 07 2008, 05:33PM

Registered Member #2561

Joined: Tue Jul 24 2007, 11:26PM

Posts: 132
Thanked 14 times in 12 posts

Hi Joseph...

Thanx so much for the reply
There was a slight mistake with hardware circuit what i did and now it is working fine.

These are the steps what i concluded with 3x4 Matrix kepad mode configuration.

Fir this first we need to train this chip for the words and after that only recognization process will be done by the chip

Step1: Power On the System

Step2: Press PIT4 Switch
( Led1 will be active to indicate that all the 12 memory banks are cleared and go to the Training mode and after that LED1 will be continuosly active)

For Training the chip

Step3: Press 1 in Keyapd ( for storing the word in memory bank1)

Step4: Speak into the mic to record into bank1 of word length of maximum of 1.5sec long (LED1 will blink once to indicate that word has been stored in the Memory bank and automatically goes to recongization mode

Step5: Press 2 Keypad ( For Storing the word in memory Bank2)

Step6: Same as Step4

Similrly proceed for the other words to store it in a different memory banks

For Recognization mode
In recognition mode LED1 will be active again waiting for an input word in the mic.
Then if the input word matches any stored word, LED2 will be high and perticular memory bank where this recognized word has been stored will be the o/p on the Port A by clearing of the perticular port pin . Else LED1 will flash for the 3 seconds to indicate no match and then again revert to recognition mode.
If a match was found and LED2 had become active, it will remain in that state for 3 minutes and then revert to recognition mode.

Regards
Sanath
Bangalore

“You get the best out of others when you give the best of yourself “

With Regards,

Sanath Kumar
Mangalore/ Bangalore/Pune

Email: sanathmcx@rediffmail.com

" Embedded System is my Passion "

sashijoseph

Wed May 07 2008, 05:45PM

Registered Member #5870

Joined: Mon Feb 04 2008, 06:26PM

Posts: 552
Thanked 124 times in 117 posts

Hi Sanath.....
glad you got it working.
Tell us one thing...does it retain the recording even after power off?
And what's the cost of the chip?

Let there be music........

SANATH EMBEDDED

Wed May 07 2008, 05:57PM

Registered Member #2561

Joined: Tue Jul 24 2007, 11:26PM

Posts: 132
Thanked 14 times in 12 posts

Hi Joseph,
I bought this chip ( AP7003-02) from NSK Electronics Bangalore and it costs around Rs.200/ or
it is also available in
Aplus India
Ground Floor, Bakul Baug, Vasundhara,
Opp. India Bank, S.V. Road,
Santacruz(w). Mumbai - 400 054.
Off: 022-2618 2082 / 26173575
Fax: 022-2611 8035
Web : www.aplusindia.net
E-Mail: sales@aplusindia.net

With Regards,

Sanath Kumar
Mangalore/ Bangalore/Pune

Email: sanathmcx@rediffmail.com

" Embedded System is my Passion "

SANATH EMBEDDED

Wed May 07 2008, 06:14PM

Registered Member #2561

Joined: Tue Jul 24 2007, 11:26PM

Posts: 132
Thanked 14 times in 12 posts

Hi,
This is me again...

Can anyone tell me the Memory Bank what this Chip is having volatile or Non-volatile memory since in the datasheet it is not mentioned.

After power Off I tried continuosly with telling the same word what has been recored previously but the LED1 will be continusly OFF means it is not any input word. That is what I confused whether the recording will retain after the power goes Off. Can anyone help me in this.

Regards
Sanath
Bangalore

“You get the best out of others when you give the best of yourself “

With Regards,

Sanath Kumar
Mangalore/ Bangalore/Pune

Email: sanathmcx@rediffmail.com

" Embedded System is my Passion "