News Item: Frequency Counter using AT89C2051 and LCD (Assembly)
(Category: 8051 Projects)
Posted by ajay_bhargav
Wed Oct 28 2009, 02:57 am
A very simple easy to make Frequency counter project. This project is powered with small AT89C2051 microcontroller with LCD. Block Diagram of circuit is shown below. It can support a wide range of frequency input starting from 1Hz to ~16.5Mhz, rest depends on pin characteristics.
Theory of Operation
As we all know frequency of a signal is number of cycles per second. I made use of this logic to calculate frequency of the input signal.
8051 has two timers, Timer 0 is configured for 1 second delay to sample the input signal and Timer 1 is used as a counter to calculate number of cycles in that 1 second. If timer1 overflows then the overflow is counter in another register which is considered as the high byte of Frequency. Input signal is provided at P3.5/T1 which is input for Timer 1 in counter mode. LCD is connected to microcontroller port 1 in 4-bit mode. Currently program is using 2 Line LCD but it can be used for 1 line LCD too.
Program initializes the Timer0 in 16-bit mode with 50mS delay value, a tick value of 20 is loaded to have total delay of 1s (50 x 20 = 1000 mS). Timer 1 is configured in 16-bit counter mode. After a sample of 1 sec, we get the number of cycles hence the frequency of input signal from timer1 registers (TH1:TL1) and high byte of Frequency. So total 3 byte value is then converted to a decimal equivalent represented in hex. This decimal value is then updated to LCD. The whole process repeats again.
![]()
For any doubts and suggestions please use forum
Download: Frequency Counter using AT89C2051 and LCD (Assembly)
This news item is from Rickey's World of Microcontrollers & Microprocessors
( http://www.8051projects.net/news.php?extend.123 )
(Category: 8051 Projects)
Posted by ajay_bhargav
Wed Oct 28 2009, 02:57 am
A very simple easy to make Frequency counter project. This project is powered with small AT89C2051 microcontroller with LCD. Block Diagram of circuit is shown below. It can support a wide range of frequency input starting from 1Hz to ~16.5Mhz, rest depends on pin characteristics.
Theory of Operation
As we all know frequency of a signal is number of cycles per second. I made use of this logic to calculate frequency of the input signal.
8051 has two timers, Timer 0 is configured for 1 second delay to sample the input signal and Timer 1 is used as a counter to calculate number of cycles in that 1 second. If timer1 overflows then the overflow is counter in another register which is considered as the high byte of Frequency. Input signal is provided at P3.5/T1 which is input for Timer 1 in counter mode. LCD is connected to microcontroller port 1 in 4-bit mode. Currently program is using 2 Line LCD but it can be used for 1 line LCD too.
Program initializes the Timer0 in 16-bit mode with 50mS delay value, a tick value of 20 is loaded to have total delay of 1s (50 x 20 = 1000 mS). Timer 1 is configured in 16-bit counter mode. After a sample of 1 sec, we get the number of cycles hence the frequency of input signal from timer1 registers (TH1:TL1) and high byte of Frequency. So total 3 byte value is then converted to a decimal equivalent represented in hex. This decimal value is then updated to LCD. The whole process repeats again.
For any doubts and suggestions please use forum
Download: Frequency Counter using AT89C2051 and LCD (Assembly)
This news item is from Rickey's World of Microcontrollers & Microprocessors
( http://www.8051projects.net/news.php?extend.123 )