8051 Microcontroller Projects AVR PIC Projects Tutorials Ebooks Libraries codes : Forum / topic

connecting mobile with hyperterminal

Tue, 04 Mar 2008 00:04:21 -0800

I want to use nokia 6030 with serial cable. I have tried At commands with hyperterminal many times but it doesn't respond. On the contrary, mobimb suit software works fine with that cable. I want to receive sms through hyperterminal. Kindly help me out.

Re: connecting mobile with hyperterminal

Tue, 04 Mar 2008 08:08:00 -0800

are you sure it supports AT commands?
what are the settings you used for connection?

Re: connecting mobile with hyperterminal

Tue, 04 Mar 2008 13:14:25 -0800

I HAVE SAME PROBLEM BUT IN 6100$6210$6310I ALL OF THEM SUPORT AT COMMAND
BUT IT DASN'T WORK YET
PLEASE HELP US.............

Re: connecting mobile with hyperterminal

Sun, 09 Mar 2008 07:14:06 -0700

just check gain ... remeber to send commands followed by "\r"

Re: connecting mobile with hyperterminal

Sun, 09 Mar 2008 09:00:28 -0700

\r = 0x0D in hex

Re: connecting mobile with hyperterminal

Sat, 08 Mar 2008 23:25:05 -0800

info:
6310 supports AT commands and can be connected to microcontrollers

Re: connecting mobile with hyperterminal

Sun, 09 Mar 2008 22:17:02 -0700

Hi,
By considering that you all are using GSm phones with Modem Enabled, I would like to share some experience on it. first configure your mobile as modem in your PC, then call that modem in your Hyper terminal. and type AT -> then press ENTER, expected response is "OK". then send command ATE1 followed by enter again
then AT&W -> enter. the setting will be written on modem.One more thing you can check with.if you find your modem sets with some port no. then call direct that port in your Hyper terminal.

Re: connecting mobile with hyperterminal

Mon, 10 Mar 2008 02:20:17 -0700

Hi,
How can I figure out that modem is enabled. Sir after your reply I connect my mobile with pc with the same f bus cable. My mobile 6030 is not configured as modem. But Mobimb software works fine. It detects my mobile automatically and show all internal files except inbox.

Sir can you give me any sony ericsson mobile model number which supports at commands and complete detail of it. I heard that sony ericsson mobiles are easy to handle with at commands.

plz help me out, I have to submit a report and demo.

Re: connecting mobile with hyperterminal

Mon, 10 Mar 2008 05:13:05 -0700

just check hyper terminal setting

Bit rate 9600, check com port COM1,COM2, or etc.,control flow none,data bit 8, Must be accurate

www.developershome.com

Gurpreet

Re: connecting mobile with hyperterminal

Mon, 10 Mar 2008 06:11:26 -0700

Amin Sharif wrote ...

Sir can you give me any sony ericsson mobile model number which supports at commands and complete detail of it. I heard that sony ericsson mobiles are easy to handle with at commands.

plz help me out, I have to submit a report and demo.

so you gave up 6030??? ok you can use sony ericsson T290i

Re: connecting mobile with hyperterminal

Mon, 17 Mar 2008 01:12:03 -0700

Is it possible to change the baud rate of T290i sony ericsson at 9600. All they support is 115200 bps.

Re: connecting mobile with hyperterminal

Mon, 17 Mar 2008 11:12:12 -0700

Amin Sharif wrote ...

Is it possible to change the baud rate of T290i sony ericsson at 9600. All they support is 115200 bps.

wrong info

Re: connecting mobile with hyperterminal

Mon, 17 Mar 2008 10:04:49 -0700

Did you try at 9600?

if not then do this... connect at 115200bps then send this AT command

AT+IPR=9600

it will set baudrate at 9600.

Re: connecting mobile with hyperterminal

Tue, 18 Mar 2008 02:15:33 -0700

I don't understand. what is wrong info.

Re: connecting mobile with hyperterminal

Tue, 18 Mar 2008 02:29:09 -0700

it connects at 9600

Re: connecting mobile with hyperterminal

Tue, 18 Mar 2008 02:56:24 -0700

Can you tell me which mobile can be used with 9600 baud rate. I have the limitation of 9600. The mobile must support At commands too. Please I am in deep trouble.

Re: connecting mobile with hyperterminal

Tue, 18 Mar 2008 04:14:46 -0700

t290i

Re: connecting mobile with hyperterminal

Tue, 18 Mar 2008 10:37:20 -0700

why only 9600? and whats the trouble?

Re: connecting mobile with hyperterminal

Tue, 18 Mar 2008 11:17:07 -0700

try AT + IPR = to change baud rate
then AT&W to set the config to memory!!

Re: connecting mobile with hyperterminal

Thu, 20 Mar 2008 06:54:40 -0700

The trouble is this I am using 89c52 which can support maximum 19200.
I am glad to say that I bought the t290i used and connect with hyperterminal. It works fine with all at commands and with 9600 baudrate. Hurrah!. Thanks to all you guys. You all are great working guys. Hard ware is fine. Now I have to ask that what is command to receive current unread sms. and sms from sim card. and how can I be indicated that new sms is arrived.

Re: connecting mobile with hyperterminal

Thu, 20 Mar 2008 07:10:01 -0700

What i need is that any new sms comes, microcontroller is indicated about it and then mc receive that unread sms and store it in its ram. Please help me out. thanks.

Re: connecting mobile with hyperterminal

Thu, 20 Mar 2008 08:09:28 -0700

two methods for this
1> by sending AT+CNMI command to mobile phone and set it to indicate when new msg arrives
2> by sending AT+CMGR command through polling or interrupt.
For more info read AT commands manual

Re: connecting mobile with hyperterminal

Thu, 20 Mar 2008 08:21:47 -0700

well if u r using gsm modules then it is possible. Since in widely available GSM module u can't store the sms in GSM module itself so u have to fetch that to ur MC by continuous polling the GSM Module via specific commands which is supported by module. even u can monitor the signal strength by sending command via hyperterminal...

Re: connecting mobile with hyperterminal

Mon, 24 Mar 2008 02:04:33 -0700

hmm.. you can do one thing... you are already using polling method.. so..
after 3 retries of polling.. and if you are not getting any reply from phone then one thing is sure that phone is not connected. So you can put a jump to the point where you keep on sending AT and wait for OK phone other end, once you get OK, you initialize the phone in the sequence you mentioned.
AT+CMGF=1
AT+CPMS="ME"
AT+CMGL="ALL"
is it fine?

Re: connecting mobile with hyperterminal

Sun, 23 Mar 2008 23:12:21 -0700

My previous problems are solved except one, new sms indication.
I have send AT+CNMI=? many times, it responds with some setting arrangments but I don't understand. Kindly help me with complete command actually to be sent and what responses may be expected. One new problem is generated that if I disconnect com port cable and then insert it again I lose all previous setting for example.
AT
AT+CMGF=1
AT+CPMS="ME"
AT+CMGL="ALL"
and all. I have to reinitialize all those. Thanks

Re: connecting mobile with hyperterminal

Mon, 31 Mar 2008 23:30:01 -0700

Hi guys.
My problem of sms reading is solved but new sms indication to controller problem is still alive . I have sent {AT+CNMI=0,1,0,0,0 \r } many times but it responds with { +CMS ERROR: 303 }. I think my mobile T 290i doesn't support this command. If it is not possible than is there any method except polling which can give me quick response? Please help me out.

Thanks.

Re: connecting mobile with hyperterminal

Mon, 31 Mar 2008 23:41:23 -0700

It respond with something like this,
AT+CNMI=?
+CNMI: (2),(0,1,3),(0,2),(0),(0)

OK
AT+CNMI=1,1,0,0,0
+CMS ERROR: 303

solve it please.

Re: connecting mobile with hyperterminal

Tue, 01 Apr 2008 07:02:02 -0700

i also tried this.... may be this command not supported

Re: connecting mobile with hyperterminal

Tue, 01 Apr 2008 21:00:40 -0700

Hello abbas1707.
What I am doing now is taking interrupt from vibrator. It gives me 0 to 2.5v some pulses. Any suggestion for this practice or any better. Thanks

Re: connecting mobile with hyperterminal

Wed, 02 Apr 2008 02:37:13 -0700

never tried this you try and also tell us about the results

Re: connecting mobile with hyperterminal

Wed, 02 Apr 2008 06:46:15 -0700

what are you doing with vibrator o/p? i mean what purpose?

Re: connecting mobile with hyperterminal

Wed, 02 Apr 2008 08:48:52 -0700

Probably using it as a trigger for new sms indication.Neat idea if all else fails.......

Re: connecting mobile with hyperterminal

Wed, 02 Apr 2008 09:19:35 -0700

hi im doing propject which involes 8051 reads sms from mobile ...
plz giv me related technical data.........

Re: connecting mobile with hyperterminal

Wed, 02 Apr 2008 23:02:14 -0700

Yes, definitely, I am using vibrator o/p as a trigger to the microcontroller after this microcontroller initializes its sms reading routine. If new comes then save it otherwise leave it.

Re: connecting mobile with hyperterminal

Wed, 02 Apr 2008 23:06:16 -0700

Yes, we are there to help you. First get T 290i which I am using. Connect with hyperterminal with data cable and send AT . Tell us what you get.

Re: connecting mobile with hyperterminal

Mon, 28 Apr 2008 16:07:34 -0700

Dear Amin,
Sorry for so late reply. I heard from my nokia ex. colleagues that 6030 is having modem facility in it.you can configure it as modem in any computer. or best way to get downloaded PC suit from Nokia website. and it is comming with drivers for respective mobiles. hen you may able to see modem configured in your PC.

Re: connecting mobile with hyperterminal

Wed, 14 May 2008 15:13:17 -0700

congrats for successful completion of project, if you are willing please share your work with us

Re: connecting mobile with hyperterminal

Wed, 14 May 2008 13:29:29 -0700

Hi Shailesh.
Thank you very much. Good news is this that I have completed my project with T290i and big dot matrix display. What ever sms comes is displayed on big display. Now I am working on object oriented programming. I will be learning TCP IP after few weeks hopefully after Cpp and oop.
Thanks again.

Re: connecting mobile with hyperterminal

Fri, 16 May 2008 03:16:37 -0700

yes amin we will be glad if you share your project with all of us

Re: connecting mobile with hyperterminal

Sat, 07 Jun 2008 21:54:54 -0700

hi everybody,
I read all posts in this topic but I do not know. Does Nokia 6030 support AT Command? I have one but it does not work when I tried with hyperterminal, so I want to sure that Nokia 6030 does not support AT command.
Please help me.
Thank you very much
Best regards!

Re: connecting mobile with hyperterminal

Thu, 31 Jul 2008 09:40:50 -0700

hey t290i supports at command and text mode. but with serial cable? or usb cable. i'll use it with pic16f628A. so which pins i must use?(tx,rx,gnd)