Discussion in "Project Doubts" started by    Rickey    Sep 20, 2006.
Wed Sep 20 2006, 11:22 AM
#1
here is the explaination of the circuit of home automation.

the whole circuit is devided into four sections.
A. Control and Display Section
B. PC Interface Section
C. Appliance Section
D. Power Supply section

Power Supply Section: This section will provide the power to the circuit, in this i have used two ICs one is LM7805 and other LM7812. LM7805 will provide the 5V to the controller and other components. LM7812 is for extenstion purpose, if someone want to use a 12V relay then he/she can use this 12V supply.

Control and Display section: This section contain mainly two components. Microcontroller and LCD. Microcontroller is used for all the controlling purpose, ofcouse its the brain of the project. LCD is used for display the messages which are being sent over internet.
There is provision of sending message from internet terminal from where user login.
so on reciever side.. user can see messages pressing keys. there are three keys provided. one is to open/close message, second is next message and third is previous message.

PC Interface Section: In this section there is one main IC used which is very common MAX232 for RS232 interface between PC and controller. so its basically provides Serial communication.

Appliance Section: This section provides interface with Appliances to control maximum of 8 devices. i have connected LEDs to show each appliance. if LED is on that means appliance is ON. if LED is off, means appliance is off. so if you want you can replace these LEDs with relays for 220V appliance conection.

anymore quaries please reply to the post.
regards,
ajay bhargav
 N1KH1L like this.
Fri Sep 29 2006, 11:25 AM
#2
Thats a very nice Idea...And which type of communiation control is there for remote operation of the devices...I mean simple dial-up or TCP/IP?
Fri Sep 29 2006, 11:28 AM
#3
it doesnt matter how you connect to internet.. the only thing matter is what application you use to connect to the board. so i am using Telnet for the remote terminal login. hope you have worked on it.
Fri Dec 22 2006, 01:25 PM
#4
ok.will the status of led's be known to the user on transmitter side?
Thu Dec 28 2006, 08:37 PM
#5
yes, there is a command "stat" for the same. see the help file for command information.
Thu Feb 22 2007, 08:51 PM
#6
I have a question about the HA project. I was able to get the CLI project to work. Now I am trying the HA project. I am unable to get any response with the HA.hex flashed to the microcontroller. Essentially I have the circuit wired up like the CLI project. I do not have the LCD or the buttons hooked up. Could that be the reason it does not work? I am able to connect to the server but I do not get any response from the microcontroller.
Thu Feb 22 2007, 09:59 PM
#7
it will not work with all the components because it initializes LCD during the init part.
So without LCD it will not work.. better connect just an LCD thats all! and ofcourse with serial
Tue Feb 27 2007, 06:48 PM
#8
I want to remove the LCD from the HA project. I was wondering if you would be willing to look at the altered code to see if it is correct? I can email you the code if you would like.
Tue Feb 27 2007, 07:23 PM
#9

I want to remove the LCD from the HA project. I was wondering if you would be willing to look at the altered code to see if it is correct? I can email you the code if you would like.

Matt



Hi matt... can you please crate a new topic.. for your doubt?
it will be easy for u and me.. to help! and its better not to make this thread too big as.. the first reply in the thread is important.
So, create a new thread, attach your modified files with the thread
I will wait
Thu Jan 03 2008, 10:31 AM
#10
Hi Everybody.. Can anyone explain the full operation of the project home automation over internet... i need crystal clear working of circuit.. i.e; for instance , what happens when a command is given from transmitter side.. how does MC receives it.. how it is decoded.. what will MC do with program burned inside it while receiving a command???? then how will it produce signal to activate the output switches.. what type of switch must be used at output port of MC along with Power line(220v)...

why the LCD is used.. ? then which file should i burn in MC....?? what r that c programs and what should i do with it..

Plz help me out to find answers for the above questions bcoz i m not a electrical or electronic student.. i just loved this project.. so i need to do that .. so help me..


regards,
Nivas

Get Social

Information

Powered by e107 Forum System

Conversation

Mon Mar 27 2017, 04:09 AM
priyanja awate
my project is greenhouse monitering and controlling using 8051 .can u give me the program of this project
ExperimenterUK
Sat Mar 25 2017, 09:56 PM
@Noreen I suggest you log in and post a full description of what you need in our PIC forum
Sat Mar 25 2017, 03:10 PM
Noreen
Hello I worked on a project related to Wireless Electricity theft detection using GSM during my bachelors. I used Nokia 6230 for sending sms using AT commands. I chose to work with SMS text mode. The microcontroller I used was PIC16F877A and its software coding done through PIC Basic Pro. Unfortunately, I lost my account password and do not have coding for generation sms using AT commands. I need that coding. Can some one help me to provide complete Pic Basic Pro code. In which step by step guidance is given so that I can understand easily. Regards,
Wed Mar 22 2017, 09:13 PM
ajay kumar
help me nokia lcd light
Wed Feb 22 2017, 06:14 AM
ChollyMo
Indeed, on the LCD tutorial, many missing Tables and figures !!
Wed Feb 22 2017, 06:06 AM
ChollyMo
I don't see any Table 3. I'm using Chrome.
Fri Feb 03 2017, 05:56 AM
irfan shaikh
hi, i want interface WS2811 pixel led using NUVOTON N79E352, but i dont know how to code it. can anyone help me or provide me sample coding for interfacing WS2811 PIXEL LED. THNX
Thu Jan 19 2017, 08:42 PM
abhays
Hi...i have made a circuit for interfacing PT100 with LM358 whose temperature is shown on the LCD...But the temperature is not getting incresed slowly ..a small change directly increses the temp...can any one help me
Thu Jan 19 2017, 04:27 PM
roba
send me alarm clock simulation using proteus software
Mon Jan 16 2017, 03:15 PM
Rutuja
How can we read notepad file using random acess file

Downloads

Comments

SAUnwin
Tue Mar 21 2017, 02:29 PM
letonarolikah
Mon Mar 20 2017, 11:21 AM
nerodear
Tue Mar 14 2017, 07:08 AM
XuZiling
Wed Feb 22 2017, 02:40 AM
diwakar_96
Thu Feb 16 2017, 02:40 PM
Helia
Thu Feb 09 2017, 09:59 AM
fasihaftab
Sat Jan 28 2017, 08:58 AM
jmunjr
Tue Jan 17 2017, 06:25 PM

Online

Guests: 60, Members: 0 ...

most ever online: 182184
(Members: , Guests: 182184) on 06 Aug 2010: 05:37 AM

Members: 37804
Newest member: SAUnwin
Forum Activity
ExperimenterUK Avatar
Posted By ExperimenterUK
Sat Mar 25 2017, 09:49 PM
I have attached code showing one method you could ...
Deepakvaishu Avatar
Posted By Deepakvaishu
Sat Mar 25 2017, 07:59 AM
I am using Keil and 8051 microcontroller
ExperimenterUK Avatar
Posted By ExperimenterUK
Fri Mar 24 2017, 06:05 PM
The best way is to use an interrupt to run the cou...
Deepakvaishu Avatar
Posted By Deepakvaishu
Fri Mar 24 2017, 05:22 AM
Hi,I got that we should use timer......But I am a ...
ExperimenterUK Avatar
Posted By ExperimenterUK
Thu Mar 23 2017, 09:14 PM
You have largely answered your own question.Use on...
ExperimenterUK Avatar
Posted By ExperimenterUK
Thu Mar 23 2017, 07:03 AM
I have looked at your code.I think you are confuse...
Deepakvaishu Avatar
Posted By Deepakvaishu
Thu Mar 23 2017, 05:34 AM
hello,I can type the letters now when the particul...
SAUnwin Avatar
Posted By SAUnwin
Tue Mar 21 2017, 02:55 PM
HI,There are two ways I'd tackle thiss.Key down on...
Deepakvaishu Avatar
Posted By Deepakvaishu
Mon Mar 20 2017, 08:24 AM
hello,I am using a keypad to type the text message...
Helia Avatar
Posted By Helia
Thu Mar 16 2017, 09:15 AM
hi.. the following code is not working on hardware...