Discussion in "Project Doubts" started by    Chinmay Das    Mar 10, 2009.
Thu Feb 04 2010, 04:46 PM
..


[ Edited Tue Feb 16 2010, 03:48 PM ]
Wed Mar 10 2010, 01:12 AM
Hey guys I am facing the same problem which chinmay faced at the first run

I am getting the same boxes in my LCD bt i have checked the connections

P0.0 is connected to DB0 and so on

Plzz help me out
Wed Mar 10 2010, 07:05 PM
pullups are on place?

well these all problems are solved now. it was long back when chinmay faced these problems. so you need to check your circuit carefully. must be some wiring issues.
Thu Mar 11 2010, 04:03 AM
anybody please give me the clear circuit of humidity sensor
the image in zip is quite confusing it has got 4 terminals but the actual sensor has 3 terminals and the element in the shunt is not recognizable
also is this the hih4000-001 or other i uses hih 4000-001 sensor


[ Edited Thu Mar 11 2010, 04:05 AM ]
Mon Mar 15 2010, 11:07 AM
some body please reply
ajay sir its very urgent please help give me the clear circuit of humidity sensor

Tue Mar 16 2010, 03:43 PM
Gaurav i already replied you.

open datasheet of HIH sensor, and there are only 3 pins -ve, o/p and +ve all goes to right place. there is a cap and resistance between -ve and o/p and +ve goes to VCC.

dont confuse youself with the above circuit too much. If you can update the circuit later on please do it, I would update the project considering your contribution to it.
 gaurav007 like this.
Tue Mar 16 2010, 03:49 PM
ok i get the point thanks once again
Wed Mar 31 2010, 07:56 PM
i hav finished the hardware work
I am facing the same problem which chinmay faced at the first run

I am getting the same boxes in my LCD bt i have checked the connections

P0.0 is connected to DB0 and so on

Plzz help me out
Thu Apr 03 2014, 05:05 PM
only changes in varible resistor(between vcc,gnd & 3 pin of lcd contrast chnge)...as like 0 ohm...otherwise you coonect lcd wrong way..

Get Social

Information

Powered by e107 Forum System

Conversation

Sun May 20 2018, 06:01 PM
justinb
how to write and execute a program that read the keypad button and display the number on 7 segment on intel8051 at89s52 in assembly language?
Sun May 20 2018, 05:56 PM
justinb
how to write and execute a program that read the keypad button and diplay the number on 7 segment ?
Sun May 20 2018, 01:44 PM
StephenTitly
https://coindump.biz/?ref=0110ce0e15d11860f5c787dd7668239a
Thu May 17 2018, 02:36 PM
HAMZA TAJ
sir iwant to ask about controller of three phase supply by using back to back thyristor instead of triac....will u give me some guideline?
Sat Apr 28 2018, 08:54 PM
ashutosh jain
IR Remote Switch using TV remote (RC5 Protocol) is not working properly. opp1 & opp2 is in problem.plz help
ExperimenterUK
Sat Apr 28 2018, 04:09 AM
@kaiserslautern Post in forum
Wed Apr 25 2018, 03:09 PM
kaiserslautern
Hello everyone, using software uart is a very good idea for a second serial port. Thank you so much. I would kindly like to know how to connect this port to the PC?
ExperimenterUK
Sun Apr 22 2018, 03:50 AM
This is a community site. Feel free to help anyone needing advice
hareeshchamiyar
Thu Mar 29 2018, 06:47 PM
please help me for the configuration bits for dspic30f2010
hareeshchamiyar
Thu Mar 29 2018, 06:45 PM
can any one using dspic30f2010.

Downloads

Comments

bdmehta
Tue May 22 2018, 02:30 AM
kmag1953
Sun Apr 29 2018, 07:09 PM
udiwonder
Sat Apr 28 2018, 12:41 PM
pirpiri
Sat Apr 21 2018, 03:35 PM
Pater
Fri Apr 20 2018, 02:38 PM
jamiel
Sat Apr 14 2018, 12:47 AM
akrepkral76
Wed Apr 04 2018, 07:51 PM
samanthaeaves
Mon Apr 02 2018, 06:27 AM

Online

Guests: 50, Members: 0 ...

most ever online: 182184
(Members: , Guests: 182184) on 06 Aug 2010: 05:37 AM

Members: 37998
Newest member: bdmehta
Forum Activity
ExperimenterUK Avatar
Posted By ExperimenterUK
Mon May 14 2018, 10:17 PM
So the main problem is that I am not getting Analo...
ExperimenterUK Avatar
Posted By ExperimenterUK
Mon May 14 2018, 09:40 PM
Hi sir after checking all the connection i...
Pater Avatar
Posted By Pater
Mon May 14 2018, 05:36 PM
Basically my project is based on Data Acquisition ...
LAMBO Avatar
Posted By LAMBO
Sun May 13 2018, 02:13 PM
Hi sir after checking all the connection i...
ExperimenterUK Avatar
Posted By ExperimenterUK
Mon May 07 2018, 07:27 PM
This design should be fine.Choose a frequency betw...
Pater Avatar
Posted By Pater
Mon May 07 2018, 01:28 PM
Sorry for late reply as exams were on,Based on my ...
ExperimenterUK Avatar
Posted By ExperimenterUK
Thu May 03 2018, 03:32 PM
If the circuit works with a light bulb, the probl...
LAMBO Avatar
Posted By LAMBO
Thu May 03 2018, 08:04 AM
Hi sir as u mentioned above everthing is working...
ExperimenterUK Avatar
Posted By ExperimenterUK
Wed May 02 2018, 08:28 PM
Thanks for the video clip, it's a good idea.Electr...
LAMBO Avatar
Posted By LAMBO
Wed May 02 2018, 10:53 AM
Hi sir did the changes as per instructions. ...