Discussion in "8051 Discussion Forum" started by    carlos_10111    Nov 6, 2009.
Fri Nov 06 2009, 10:43 AM
#1
Hi every one, i'm trying to use proteus virtual terminal for serial communication.
But i'm getting funny characters on the display. i tried using the code from the tutorial, it shows nothing, but the one i coded is showing but not what i'm expecting.
the code is just suppose to show a character on the vTerminal. here is the code and the circuit.
#include <REGX51.H>


void delay(int);
void SerTx(unsigned char x);
void serial_send(unsigned char dat);
void serial_init();
unsigned char serial_read();
void main()
{
 
while(1)
{  
     serial_init();
     SerTx('c'); // this is my function
     serial_send('C'); //tutorial function
              
	
}

}

void SerTx(unsigned char x)
{
  	SBUF =x;
	while (TI==0);
	TI = 0;

} 

void serial_init()
{	
	TMOD =0x20;
             SCON =0x50;
	TH1= 0xFD;
	TL1= 0XFD;
 	TR1 = 1;

}

void delay(int cnt)
{
   int x,y;
   for(x = 0; x < cnt;x++);
   	for (y=0;y<100;y++);
   			
 }  
void serial_send(unsigned char dat)
{
	while(!TI);
	TI = 0;
	SBUF = dat;
}

unsigned char serial_read()
{

	while(!RI);
	RI = 0;
	return SBUF;
}





As you can see from the terminal window, instead of showing 'c' it showing a quarter (1/4).
I tried changing the font type, still get the same error.

Please help out!
Fri Nov 06 2009, 11:30 AM
#2
comment this serial_send('C'); from while loop.

and take serial_init function out of while loop as its required only once.
Mon Nov 09 2009, 11:25 AM
#3
Thanx Ajay, but i'm still getting the same errror!
How do you use the serial_send function? is the structure of my code fine?
I have a feeling the problem is not with the function, because it sending the information, it's only that the characters are displayed in a format that i don't understand. if i transmit A, i get a funy character!

Mon Nov 09 2009, 11:52 AM
#4
probably you did not set the correct baud rate.

open virtual terminal properties and see what baud is set there. try not to use max232 in simulation, coz its of no use in virtual circuit debugging.
Wed Nov 11 2009, 08:08 AM
#5
Hi Ajay, yes i tried removing the max232, but still getting the same problem.
the baud rate i'm using is 9600, which is the same i did setup in the program.
Let me try to use a lower baud rate and see what happens
Thanx again,
Wed Nov 11 2009, 08:25 AM
#6
Nop, still getting the same problem. here are the changes i have made to the circuit as well as the program. Here is how my codes looks like:


#include <AT89X51.H>


void delay(unsigned int ) ;
void SerTx(unsigned char );
void serial_send(unsigned char );
void serial_init();
unsigned char serial_read();

void main(void)
{
serial_init(); 
while(1)
{  


	
	serial_send('B');

	serial_send('C');

	serial_send('D');


	
}

}

void SerTx(unsigned char x)
{
  	SBUF =x;
	while (TI != 1);
	TI = 0;

} 

void serial_init()
{	
	TMOD =0x20;
    SCON =0x50;
	TH1= -6;
	TR1 = 1;

}

  
void serial_send(unsigned char dat)
{  
	SBUF = dat;
	while(TI == 0);
	TI = 0;
	
}

unsigned char serial_read()
{

	while(RI == 0);
	RI = 0;
	return SBUF;
} 
void delay(unsigned int cnt)
{	int x;
	for (x=0; x < cnt; x++)
	{
	TMOD = 0x10;
	TH1 = 0xC5;
	TL1 = 0x68;
	TR1 = 1;
	while(TF1 != 1 );
	TR1 = 0;
	TF1 = 0;
	}
} 







This picture is showing what im getting after i transmit B,C and D




Thanx for your help once again!
Wed Nov 11 2009, 12:22 PM
#7
hi carlos_10111,

Looks to me that you are messing up with timer 1!

void SerTx(unsigned char x)
{
        SBUF =x;
        while (TI != 1);
        TI = 0;
}

void serial_init()
{      
        TMOD = 0x20;
        ------------
        ......
}
void delay(unsigned int cnt)
{       int x;
        for (x=0; x < cnt; x++)
        {
        TMOD = 0x10;
        TH1 = 0xC5;
        TL1 = 0x68;
        TR1 = 1;
        while(TF1 != 1 );
        TR1 = 0;
        TF1 = 0;
        }
}



Your serial_init() configures T1 in auto reload mode and delay() in mode 1!
If you want to use UART. you must not modify Timer 1 as it is hardwired to clock the UART. Besides you are overwriting the baud rate (-6) values in delay().
I guess if you use timer 0 in delay, your program would work fine.

BTW I would prefer using assembly for delay kind of operations.
One more suggestion is for your delay function. You can rewrite it as :
void delay(unsigned int cnt)
{       int x;
        
        TMOD = 0x10;
        TH1 = 0xC5;
        TL1 = 0x68;
        TR1 = 1;
                     
        for (x=0; x < cnt; x++)
        {
             while(TF1 != 1 );
             TH1 = 0xC5;
             TL1 = 0x68;
             TF1 = 0;
        }
}


Cheers
Sarma
Wed Nov 11 2009, 01:28 PM
#8
Thanx for your help sarma, but it looks the problem is not with the delay. here is the modified code. i commented out the delay, but still get the same problem!

#include <AT89X51.H>


//void delay(unsigned int ) ;
void SerTx(unsigned char );
void serial_init();
unsigned char serial_read();

void main(void)
{
serial_init(); 
while(1)
{  


	
	SerTx('B');

	SerTx('C');

	SerTx('D');


	
}

}

void SerTx(unsigned char x)
{
  	SBUF =x;
	while (TI != 1);
	TI = 0;

} 

void serial_init()
{	
	TMOD =0x20;
    SCON =0x50;
	TH1= -6;
	TR1 = 1;

}

 

unsigned char serial_read()
{

	while(RI == 0);
	RI = 0;
	return SBUF;
} 


/*void delay(unsigned int cnt)
{	int x;
	TMOD = 0x01;
	TH0 = 0xC5;
	TL0 = 0x68;
	TR0 = 1;
	for (x=0; x < cnt; x++)
	{

	while(TF0 != 1 );
	TH0 = 0xC5;
	TL0 = 0x68;
	TF0 = 0;
	}
}  */


Here is some setup for the virtual terminal, may be i'm not configuring it properly.



Can someone look at this? i can't be stuck on this please!
Wed Nov 11 2009, 09:17 PM
#9
you have kept Send XON/XOFF as yes. make it no. coz we are not using any flow control in transmission.
Thu Nov 12 2009, 05:03 AM
#10
Here are some debug tips:

1. check the baud rate! Did you set TH1 for 4800 baud rate, some times we miscalculate the number loaded to TH1.

2. Are you sure that the characters are received and transmitted, i.e. is the communication between PC and your controller is established? Are there any debug LEDs connected to Tx and Rx lines which blink when you Transmit/receive any character, or some thing of that kind to be sure that the transmission and reception is happening properly.

3. check your clock speed and crystal frequency when initiating the timer. I assume that the value(-6) you used here for a 12 clock mode micro-controller with standard 11.XXX MHz crystal.

If you are sure about 1 and 2 then try setting your Vterminal's baud rate to other numbers. This is a random process! This may or may not work.
 carlos_10111 like this.

Get Social

Information

Powered by e107 Forum System

Conversation

Wed Jan 22 2020, 06:16 PM
MINU CHAUDHARY
I m getting errors while simulation process during interfacing socket output and lcd... Can i get the report of ur project which is same as us.
Tue Jan 14 2020, 07:08 AM
shubham kharade
when i am trying to simulate the program in Proteus 8 professional, I am getting some errors as cannot find module file dhtxx.md can u help me
Tue Dec 17 2019, 01:44 PM
Devangi
hello..i am programming industrial timer using 8051 with 24lc64 eeprom. i have query in storing the 3 diff value in eeprom with enter button. can anyone share c code ?
Tue Dec 17 2019, 10:30 AM
Andrius
Hello. Can anyone share the code in Bascon and scheme in Proteus?
Thu Nov 21 2019, 12:30 PM
raj2555
how to interface 8051 microcontroller with NRF24L01+ module
ExperimenterUK
Sat Oct 12 2019, 10:23 PM
Log in.. then post your code in the 8051 forum
Sat Oct 12 2019, 10:18 AM
Bhadra Sajikumar
i am doing a countdown timer with 8051 for my project, unfortunately our professor had to take a leave of absence before he could teach us most of it.. can someone explain the .asm code of it for me?
Mon Sep 23 2019, 07:37 AM
Nathaniel
I am doing a project for my schools wireless security system with cameras,sensors and spot lights using 8051 micro controller, could you help me out with the design and its source code.
Wed Sep 18 2019, 08:48 PM
Caryn Kover
Thank you for your time,
ExperimenterUK
Mon Aug 05 2019, 07:09 PM
@Ismail ..post in forum, give details

Downloads

Comments

wounder
Sat Jan 25 2020, 12:09 PM
brucewilliams20
Thu Jan 23 2020, 11:47 AM
Nippy56
Sun Jan 19 2020, 02:13 AM
usb5962
Sat Jan 11 2020, 10:42 AM
elt
Tue Jan 07 2020, 06:53 PM
mg3914697
Tue Jan 07 2020, 12:42 PM
afds43
Sun Dec 29 2019, 05:54 AM
Rupeshpatil
Fri Dec 27 2019, 06:14 PM

Online

Guests: 34, Members: 0 ...

most ever online: 182184
(Members: , Guests: 182184) on 06 Aug 2010: 05:37 AM

Members: 38118
Newest member: wounder
Forum Activity
ExperimenterUK Avatar
Posted By ExperimenterUK
Sun Jan 26 2020, 04:05 AM
For a 12MHz crystal using a normal divided by 12 c...
wounder Avatar
Posted By wounder
Sat Jan 25 2020, 12:14 PM
I have a 8051 micro controller ,it has timer0,1,2,...
brucewilliams20 Avatar
Posted By brucewilliams20
Sat Jan 25 2020, 08:25 AM
Also, does anyone knows a platform where I can liv...
brucewilliams20 Avatar
Posted By brucewilliams20
Sat Jan 25 2020, 08:17 AM
Hi Mirza,That match and the politics, both are fin...
ExperimenterUK Avatar
Posted By ExperimenterUK
Fri Jan 17 2020, 10:24 PM
We will need the circuit diagram.A Proteus simulat...
Billz Avatar
Posted By Billz
Sat Jan 11 2020, 05:43 PM
hi everyone please attached files are my c code fo...
ExperimenterUK Avatar
Posted By ExperimenterUK
Tue Jan 07 2020, 08:18 PM
Not a stupid question.Setting up "Eclipse" can be...
elt Avatar
Posted By elt
Tue Jan 07 2020, 07:06 PM
So i have just began learning programming micros a...
Billz Avatar
Posted By Billz
Mon Jan 06 2020, 09:22 PM
I think it would be better if you guys try to come...
ExperimenterUK Avatar
Posted By ExperimenterUK
Mon Jan 06 2020, 12:22 AM
Can you post a circuit diagram and any code you ha...