Discussion in "Chill out!" started by    coolmirza143    Aug 25, 2010.
Wed Aug 25 2010, 04:33 AM
#1
Mobile controlled Robot



This is the complete detail you can have to create your own Global Robo that can be driven by sending DTMF tones from your mobile phone!!!!!!! "" Yes!! your mobile phone""



All you need to do is to have a DTMF tone decoder IC and some capacitors and resisors to complete the circuitry along with two mobile phones and a headphone for inputting the DTMF tones into the circuitry and u r done.



The complete list of bill of materials is provided below along with the circuitry with a little explanation of how the complete circuit works.

Bill of Materials:
MT8870 dtmf decoder ic
100k resitor 2pc.
300k resistor 1pc.
3.57945Mhz crystal oscillator
0.1 uf capacitor 2pc.
4 LED
connecting wires....

Working: while the input from the mobile using a headphone is connected b/w the 0.1uf capacitor and the ground, DTMF tones can be transferred to the decoder ic(8870) and once the ic is powered up the o/p can be seen by connecting LED's at Q!, Q2, Q3 and Q4 o/p of the decoder ic.
The output on the Q1 to Q4 pins of the decoder IC has been shown in the image.

the o/p of the decoder ic then can be connected to a motor driver ic like(L298 or L293D) to drive some motors or relays as a switch to operate some devices remotely as the Mobile phone connected can be called from anywhere in the world and by pressing the keys the DTMF tones can be transmitted to the receiving end mobile and hence any device connected can be operated globally.

Working Video

[yt]kSqVPZpbxm4[/yt]

Video Link

http://www.youtube.com/watch?v=kSqVPZpbxm4&feature=related


[ Edited Wed Aug 25 2010, 05:15 PM ]
Mon Oct 18 2010, 10:11 AM
#2
I have a question.
How wud u control the device attached to that ic by sending dtmf tones? Its just by sending ? And how i am going to manipulate the outputs if let say i want to turn on Q2 for 2sec? Is that dtmf decoder ic programable?
Mon Oct 18 2010, 06:01 PM
#3
hi coolmirza143
wonderful thing

@ romel_emperado
dtmf r not programmable chip it decode analog frequencies to its digital equivalent no
Tue Oct 19 2010, 09:12 AM
#4


hi coolmirza143
wonderful thing

@ romel_emperado
dtmf r not programmable chip it decode analog frequencies to its digital equivalent no

majoka



then how would u specify if you want to turn on Q4 or Q1 of that IC? using DTMF?

as i look at the table below. that is the command in sending DTMF to control the outputs?


[ Edited Tue Oct 19 2010, 09:15 AM ]
Tue Oct 19 2010, 09:27 AM
#5
hi romel_emperado
see this animation
http://www.yavuzerol.com/dosyalar/digerpro/diger3/AnimaCM8870.gif
when button pressed on mobile some transistor on and some off then we adjust our robot logic then on which button its goes right left etc
Tue Oct 19 2010, 09:42 AM
#6
@Majoka Nice animation to understand DTMF Decoding...

See here DTMF Discussion
Tue Oct 19 2010, 09:45 AM
#7


hi romel_emperado
see this animation


when button pressed on mobile some transistor on and some off then we adjust our robot logic then on which button its goes right left etc

majoka




hi majoka since this is my first time to use DTMF in my phone let me ask a question.

when i tried to use DTMF in my phone it ask a DTMG number what particular number shud i enter?
is that in the table above shud i enter?
Tue Oct 19 2010, 09:58 AM
#8
yes you can enter any number
 romel_emperado like this.
Tue Oct 19 2010, 10:19 AM
#9
hi romel_emperado
simple connect earphone to mobile insert ear phone into ur ear u can dial any no when u diall u will listen a specific toned across each no that r DTMF Tones
make a call to any no when he attend do not speak and press any button u will listen a tones clearly that is analog frequencies in audible range as mention in above char
decoder ic decode these frequencies to its key in binary form
encoder ic encode keys no into analog frequencies form
 romel_emperado like this.
Thu Oct 21 2010, 12:24 AM
#10


hi romel_emperado
simple connect earphone to mobile insert ear phone into ur ear u can dial any no when u diall u will listen a specific toned across each no that r DTMF Tones
make a call to any no when he attend do not speak and press any button u will listen a tones clearly that is analog frequencies in audible range as mention in above char
decoder ic decode these frequencies to its key in binary form
encoder ic encode keys no into analog frequencies form

majoka




ah okay thanks i understand that..
but the phone you are calling need to answer your call for you to send a DTMF? what if the one you are calling is not answering your call, can u still send a DTMF?

Get Social

Information

Powered by e107 Forum System

Conversation

Sun Dec 08 2019, 04:50 PM
Marti Ogrady
Take advantage of this great service today:
Thu Nov 21 2019, 12:30 PM
raj2555
how to interface 8051 microcontroller with NRF24L01+ module
ExperimenterUK
Sat Oct 12 2019, 10:23 PM
Log in.. then post your code in the 8051 forum
Sat Oct 12 2019, 10:18 AM
Bhadra Sajikumar
i am doing a countdown timer with 8051 for my project, unfortunately our professor had to take a leave of absence before he could teach us most of it.. can someone explain the .asm code of it for me?
Mon Sep 23 2019, 07:37 AM
Nathaniel
I am doing a project for my schools wireless security system with cameras,sensors and spot lights using 8051 micro controller, could you help me out with the design and its source code.
Wed Sep 18 2019, 08:48 PM
Caryn Kover
Thank you for your time,
ExperimenterUK
Mon Aug 05 2019, 07:09 PM
@Ismail ..post in forum, give details
Mon Aug 05 2019, 04:33 PM
Ismail balghmi
Hello. Please I won't download
ExperimenterUK
Wed Jul 24 2019, 12:47 AM
@BUSTER123 Please post in the forum
Tue Jul 23 2019, 06:13 PM
BUSTER123
hello! newbie here. i am kind of a guy who hates using ready - made existing libraries, so this helped a lot as i was trying to control and write to a character lcd display. however, i can't figure out how to set the cursor position. for example, i want to set it to the 5th column in the first row, so position 5. so according to the table, i am sending 10000101 on the 8 data lines of the lcd (register select pulled low). the cursor does not move there however. and i cant move the cursor left or right too. is it something wrong that i am doing? thank you.

Downloads

Comments

nabiha_anaya
Sun Dec 08 2019, 09:16 AM
ananyagupta
Tue Dec 03 2019, 07:53 AM
wells
Mon Nov 25 2019, 08:25 PM
auwal
Tue Nov 19 2019, 03:13 PM
ANKITPATEL
Mon Nov 18 2019, 11:00 AM
Casmir
Wed Nov 13 2019, 06:25 AM
DeepakBGattani
Mon Nov 11 2019, 01:31 PM
Jeanbusatta
Sun Nov 10 2019, 04:42 AM

Online

Guests: 35, Members: 0 ...

most ever online: 182184
(Members: , Guests: 182184) on 06 Aug 2010: 05:37 AM

Members: 38108
Newest member: nabiha_anaya
Forum Activity
ilylily07 Avatar
Posted By ilylily07
Sun Dec 08 2019, 01:24 PM
Hi .im humbly ask for your advice as i wrongly pur...
nabiha_anaya Avatar
Posted By nabiha_anaya
Sun Dec 08 2019, 09:19 AM
My teacher assign me a project on "voice control h...
ExperimenterUK Avatar
Posted By ExperimenterUK
Fri Nov 29 2019, 04:24 AM
" Is it possible to interface a fingerprint scanne...
ilylily07 Avatar
Posted By ilylily07
Thu Nov 28 2019, 03:50 PM
You will not find any code for an 8051 as no one w...
ExperimenterUK Avatar
Posted By ExperimenterUK
Tue Nov 26 2019, 05:44 PM
You will not find any code for an 8051 as no one w...
ilylily07 Avatar
Posted By ilylily07
Tue Nov 26 2019, 04:13 AM
I tracked down a OV7670 data sheet.The OV7670 puts...
ExperimenterUK Avatar
Posted By ExperimenterUK
Tue Nov 26 2019, 12:08 AM
I tracked down a OV7670 data sheet.The OV7670 puts...
ilylily07 Avatar
Posted By ilylily07
Mon Nov 25 2019, 04:38 PM
The 8051 has too little memory to do anything us...
ExperimenterUK Avatar
Posted By ExperimenterUK
Tue Nov 19 2019, 10:44 PM
The 8051 has too little memory to do anything us...
ilylily07 Avatar
Posted By ilylily07
Mon Nov 18 2019, 09:54 AM
0v7670 camera interfacing with stc 8051.using asse...