Discussion in "Hardware" started by    karkipreeti    Mar 14, 2013.
Thu Mar 21 2013, 09:59 AM
#11
I am glad my method is helpful If your sequence is correct your motor should always rotate in one direction.

what is the power supply rating you've used? L293D gets hot coz motor is trying to draw more current and your voltage falls down. Ultimately your circuit will go off. You might even burn your supply. check your adapter or supply rating.
Thu Mar 21 2013, 04:54 PM
#12



But as i power on my system, the motor moves a step forward and then backward and stops. the micro-controller is getting heat up.

karkipreeti


Sounds like a serious wiring error.
Check your voltage regulator.
What voltage are you putting in and getting out ?

Post your diagram.


[ Edited Thu Mar 21 2013, 04:55 PM ]
Fri Mar 22 2013, 04:29 AM
#13
i am following the circuit given in tutorial section and attaching it with this post.
a microcontroller is gone:-(. i found that the microcontroller was getting 22v at the supply pins. i have checked all the connections, they are as per the diagram attached.i have confusion about vcc1 and vcc2 of the l293 ic.

Fri Mar 22 2013, 06:01 AM
#14
22v? Did you go through datasheet of L293? and it looks like your coils are swapped thats the reason your motor is moving step forward and backwards. Check coils again... they motor should go in one direction after supply is applied.

It would be better if you can post your power supply circuit on forum. We can review it for you.
Fri Mar 22 2013, 06:07 AM
#15
I think I made mistake in tutorial schematic. the unipolar connections to L293 are swapped whereas bipolar stepper are fine. Pin 16 should have 5V and pin 8 goes to stepper voltage. I will update this today
 karkipreeti like this.
Fri Mar 22 2013, 11:35 AM
#16
i think that was the only prblm :-( now the stepper motor is working fine :-)
Mon Mar 25 2013, 04:38 AM
#17
I am sorry for wrong directions. Mistakes happens once in a while even from experience people good job and thanks for bringing this up.

Get Social

Information

Powered by e107 Forum System

Conversation

Thu Nov 21 2019, 12:30 PM
raj2555
how to interface 8051 microcontroller with NRF24L01+ module
ExperimenterUK
Sat Oct 12 2019, 10:23 PM
Log in.. then post your code in the 8051 forum
Sat Oct 12 2019, 10:18 AM
Bhadra Sajikumar
i am doing a countdown timer with 8051 for my project, unfortunately our professor had to take a leave of absence before he could teach us most of it.. can someone explain the .asm code of it for me?
Mon Sep 23 2019, 07:37 AM
Nathaniel
I am doing a project for my schools wireless security system with cameras,sensors and spot lights using 8051 micro controller, could you help me out with the design and its source code.
Wed Sep 18 2019, 08:48 PM
Caryn Kover
Thank you for your time,
ExperimenterUK
Mon Aug 05 2019, 07:09 PM
@Ismail ..post in forum, give details
Mon Aug 05 2019, 04:33 PM
Ismail balghmi
Hello. Please I won't download
ExperimenterUK
Wed Jul 24 2019, 12:47 AM
@BUSTER123 Please post in the forum
Tue Jul 23 2019, 06:13 PM
BUSTER123
hello! newbie here. i am kind of a guy who hates using ready - made existing libraries, so this helped a lot as i was trying to control and write to a character lcd display. however, i can't figure out how to set the cursor position. for example, i want to set it to the 5th column in the first row, so position 5. so according to the table, i am sending 10000101 on the 8 data lines of the lcd (register select pulled low). the cursor does not move there however. and i cant move the cursor left or right too. is it something wrong that i am doing? thank you.
ExperimenterUK
Thu Jul 11 2019, 07:55 PM
@ramos https://www.theengineeringprojects.com/2017/09/l298-motor-driver-library-proteus.html

Downloads

Comments

nabiha_anaya
Sun Dec 08 2019, 09:16 AM
ananyagupta
Tue Dec 03 2019, 07:53 AM
wells
Mon Nov 25 2019, 08:25 PM
auwal
Tue Nov 19 2019, 03:13 PM
ANKITPATEL
Mon Nov 18 2019, 11:00 AM
Casmir
Wed Nov 13 2019, 06:25 AM
DeepakBGattani
Mon Nov 11 2019, 01:31 PM
Jeanbusatta
Sun Nov 10 2019, 04:42 AM

Online

Guests: 38, Members: 0 ...

most ever online: 182184
(Members: , Guests: 182184) on 06 Aug 2010: 05:37 AM

Members: 38108
Newest member: nabiha_anaya
Forum Activity
ilylily07 Avatar
Posted By ilylily07
Sun Dec 08 2019, 01:24 PM
Hi .im humbly ask for your advice as i wrongly pur...
nabiha_anaya Avatar
Posted By nabiha_anaya
Sun Dec 08 2019, 09:19 AM
My teacher assign me a project on "voice control h...
ExperimenterUK Avatar
Posted By ExperimenterUK
Fri Nov 29 2019, 04:24 AM
" Is it possible to interface a fingerprint scanne...
ilylily07 Avatar
Posted By ilylily07
Thu Nov 28 2019, 03:50 PM
You will not find any code for an 8051 as no one w...
ExperimenterUK Avatar
Posted By ExperimenterUK
Tue Nov 26 2019, 05:44 PM
You will not find any code for an 8051 as no one w...
ilylily07 Avatar
Posted By ilylily07
Tue Nov 26 2019, 04:13 AM
I tracked down a OV7670 data sheet.The OV7670 puts...
ExperimenterUK Avatar
Posted By ExperimenterUK
Tue Nov 26 2019, 12:08 AM
I tracked down a OV7670 data sheet.The OV7670 puts...
ilylily07 Avatar
Posted By ilylily07
Mon Nov 25 2019, 04:38 PM
The 8051 has too little memory to do anything us...
ExperimenterUK Avatar
Posted By ExperimenterUK
Tue Nov 19 2019, 10:44 PM
The 8051 has too little memory to do anything us...
ilylily07 Avatar
Posted By ilylily07
Mon Nov 18 2019, 09:54 AM
0v7670 camera interfacing with stc 8051.using asse...