Discussion in "Project Doubts" started by    sankalp_s    Nov 29, 2014.
Sat Nov 29 2014, 07:59 PM
#1
hello ajay sir,
i've recently joined this forum, I've downloaded code for led chaser,
i want to infinite repetition of current running pattern through external interrupt(INT0)
when switch is on, but when switch is off then pattern should be run as previous defined time.

the code is:-

ORG 000H ; starting address
SJMP LABEL





L1 EQU P1.2 ;LED CONECTED TO THIS PORT
L2 EQU P1.3 ;LED CONECTED TO THIS PORT
L3 EQU P1.4 ;LED CONECTED TO THIS PORT
L4 EQU P1.5 ;LED CONECTED TO THIS PORT
L5 EQU P1.6 ;LED CONECTED TO THIS PORT
L6 EQU P1.7 ;LED CONECTED TO THIS PORT


LABEL:
MOV R3, #05 ;REPEtion of pattern
D7: CALL DESGN7
DJNZ R3,D7
MOV R3, #05 ;REPEtion of pattern
D8: CALL DESGN8
DJNZ R3,D8
MOV R3, #05 ;REPEtion of pattern
D9: CALL DESGN9
DJNZ R3,D9

JMP LABEL




DESGN7: CALL ALLON
CALL DELAY
SETB L1
CALL DELAY

SETB L2
CALL DELAY

SETB L3
CALL DELAY

SETB L4
CALL DELAY

SETB L5
CALL DELAY

SETB L6
CALL DELAY



CALL DELAY
SETB L6

CALL DELAY
SETB L5

CALL DELAY
SETB L4

CALL DELAY
SETB L3

CALL DELAY
SETB L2

CALL DELAY
SETB L1
CALL DELAY
RET




DESGN8: CALL ALLON
SETB L6
SETB L1
CALL DELAY
CALL ALLON
SETB L5
SETB L2
CALL DELAY
CALL ALLON
SETB L4
SETB L3
CALL DELAY

RET

DESGN9: CALL ALLON


CALL DELAY
SETB L6

CALL DELAY
SETB L5

CALL DELAY
SETB L4

CALL DELAY
SETB L3

CALL DELAY
SETB L2

CALL DELAY
SETB L1
CALL DELAY
RET

CLEAR: SETB L1
SETB L2
SETB L3
SETB L4
SETB L5
SETB L6

RET

ALLON: CLR L1
CLR L2
CLR L3
CLR L4
CLR L5
CLR L6

RET

DELAY: MOV R0,#0FFH
INLOP: MOV R1,#0FFH
DJNZ R1,$
DJNZ R0,INLOP
RET




END
Tue Dec 02 2014, 04:55 AM
#2
This program is already an infinte loop.
LABEL:
MOV R3, #05 ;REPEtion of pattern
D7: CALL DESGN7
DJNZ R3,D7
MOV R3, #05 ;REPEtion of pattern
D8: CALL DESGN8
DJNZ R3,D8
MOV R3, #05 ;REPEtion of pattern
D9: CALL DESGN9
DJNZ R3,D9

JMP LABEL

Are you looking for a particular design to be taken into loop? then you can put that design in interrupt routine itself, and keep going till the pin is high. There will be significant changes in the code. You need to understand it and then make changes.
 sankalp_s like this.
Wed Dec 03 2014, 10:15 AM
#3
Thank u very much sir, for ur response.

Actually i want to lock that pattern which is currently executing .
and when it return from interrupt then pattern should execute in their sequence.

sir please help me for the code..could u write the code?

thank u sir.

Fri Dec 05 2014, 05:08 PM
#4
We can't really understand what you want.

Do you want to freeze the display when the button is pressed. ?
Can you describe what you want in a different way.
Sun Dec 07 2014, 08:17 AM
#5
yes sir exactly as you said..
i want to freeze the display when switch is presses & when switch is not pressed then all pattern should execute in their sequence..
Wed Dec 10 2014, 04:35 AM
#6
so in ISR put a while loop till the switch is low and then as soon as it is high exit from there... processor will continue what it was doing earlier.. e.g.
    ORG 03H
    JNB P3.2, $
    RETI

So when you make INT0 low (switch pressed) it will jump to ISR and make your cpu wait till the switch is pressed.


[ Edited Wed Dec 10 2014, 04:36 AM ]
Fri Dec 12 2014, 06:29 PM
#7
Thank u sir for your response.
sir can u explain more about this or put the code in that code please.. it will be very helpful sir.

actually i've tried bit failed .. so please help me about exact code n where it would be put.

thank you.


[ Edited Fri Dec 12 2014, 07:04 PM ]
Tue Dec 16 2014, 04:55 AM
#8
ORG 000H ; starting address
SJMP LABEL1

    ORG 03H
    JNB P3.2, $
    RETI

L1 EQU P1.2 ;LED CONECTED TO THIS PORT
L2 EQU P1.3 ;LED CONECTED TO THIS PORT
L3 EQU P1.4 ;LED CONECTED TO THIS PORT
L4 EQU P1.5 ;LED CONECTED TO THIS PORT
L5 EQU P1.6 ;LED CONECTED TO THIS PORT
L6 EQU P1.7 ;LED CONECTED TO THIS PORT

LABEL1:
SETB EXT0 ; Enable external interrupt
SETB EA ; Enable interrupts

LABEL:
MOV R3, #05 ;REPEtion of pattern
D7: CALL DESGN7
; ... rest of the code ...
Wed Dec 17 2014, 04:11 PM
#9


ORG 000H ; starting address
SJMP LABEL1

    ORG 03H
    JNB P3.2, $
    RETI

L1 EQU P1.2 ;LED CONECTED TO THIS PORT
L2 EQU P1.3 ;LED CONECTED TO THIS PORT
L3 EQU P1.4 ;LED CONECTED TO THIS PORT
L4 EQU P1.5 ;LED CONECTED TO THIS PORT
L5 EQU P1.6 ;LED CONECTED TO THIS PORT
L6 EQU P1.7 ;LED CONECTED TO THIS PORT

LABEL1:
SETB EXT0 ; Enable external interrupt
SETB EA ; Enable interrupts

LABEL:
MOV R3, #05 ;REPEtion of pattern
D7: CALL DESGN7
; ... rest of the code ...

ajay_bhargav




Thank u sir.
i've tried this code but faced a syntax error on line of setb ext0.....( Symbol not defined: ext0)
sir one thing more can u give me the while loop code example for my requirement .. can i use pin int1 for this operation?

Wed Dec 17 2014, 11:21 PM
#10


i've tried this code but faced a syntax error on line of setb ext0...
( Symbol not defined: ext0)

sankalp_s


Which compilier are you using ?



sir one thing more can u give me the while loop code
example for my requirement ..

sankalp_s



ORG 03H
JNB P3.2, $
RETI

This is all the code you need to freeze the display.


can i use pin int1 for this operation?

sankalp_s


Yes, but the code changes to..
    ORG 13H
    JNB P3.3, $
    RETI

//and 
SETB EXT1 ; Enable external interrupt 1
SETB EA   ; Enable interrupts


An alternative method does not use an interrupt.
Monitor the key in the delay routine.
DELAY: MOV R0,#0FFH
INLOP: MOV R1,#0FFH
buttonTest:             ;button is the input pin 
JNB button, buttonTest  ;wait while pressed
DJNZ R1,buttonTest
DJNZ R0,INLOP
RET

Get Social

Information

Powered by e107 Forum System

Conversation

Mon May 08 2017, 12:45 PM
ivan muvunyi
please can you send me wiring diagram for automatic control of 3 phase induction motor for production of maize flour
Wed May 03 2017, 08:39 PM
imran qureshi
hello friend
Sun Apr 30 2017, 05:49 AM
Lijin G Varghese
Can u send me the circuit diagram for Program to interface GSM Module with 8051 microcontroller (AT89C51) using PC and LCD
Fri Apr 28 2017, 03:47 PM
SANDEEP T S
I need pcb wizard 3.5 version kindly send valid link of yours
ExperimenterUK
Mon Apr 17 2017, 11:56 PM
Sorry..We had a problem with registration.Confirmation emails were not sent.Please re-register
Thu Apr 13 2017, 07:29 PM
Piyush Aughad
I want circuit & program for radar detection using Microcontroller 8051
Tue Apr 11 2017, 03:27 AM
Shabbir Ahmed
Hi Ajay ....hope you and your family all will be fine are you working on andriod aplications if yes then plz reply me
Sun Apr 09 2017, 06:33 PM
ATHULYA NAIR
Dear Sir, I need to know what are the complexity for programming in 8051 Microcontroller for three phase inverter?
Sun Apr 09 2017, 06:32 PM
ATHULYA NAIR
Dear Sir,
Sun Apr 09 2017, 04:43 AM
Rohit chandra joshi
Sir I need ur help urgently.i am trying to make pc controlled led scrolling display using 8051.when i am trying to generate hex file of the code that is given by pratik suthar.it gives the error Target not created Limit:0800h I am using keil uvision4 software. Even i have tried to burn the given hex file that is atteched with the code but my led are not glowing. Pls help me sir .i struck in this problem from last month and till now i am not able to short out the problem. Pls suggest me to solve the problem.mail me at [email protected] Thanks

Downloads

Comments

lubnakhan
Sat May 20 2017, 10:23 AM
Utsavi
Wed May 17 2017, 10:35 AM
Samimash
Tue May 16 2017, 01:15 PM
gangusa
Mon May 15 2017, 04:34 AM
raghuzala
Sun May 14 2017, 02:32 PM
Prakashlimbachiya
Sat May 13 2017, 07:34 AM
east
Fri May 12 2017, 08:16 AM
ajay24
Fri May 12 2017, 08:09 AM

Online

Guests: 49, Members: 0 ...

most ever online: 182184
(Members: , Guests: 182184) on 06 Aug 2010: 05:37 AM

Members: 37827
Newest member: lubnakhan
Forum Activity
ajay_bhargav Avatar
Posted By ajay_bhargav
Fri May 19 2017, 10:17 AM
I think you are asking in the wrong forum. We do n...
ajay_bhargav Avatar
Posted By ajay_bhargav
Fri May 19 2017, 10:16 AM
You should start with something, We will help you ...
ajay_bhargav Avatar
Posted By ajay_bhargav
Fri May 19 2017, 07:01 AM
To me it looks like your development environment i...
ExperimenterUK Avatar
Posted By ExperimenterUK
Thu May 18 2017, 11:28 PM
Linux can be a minefield of make files, scripts an...
ExperimenterUK Avatar
Posted By ExperimenterUK
Thu May 18 2017, 11:18 PM
Can you provide me a demo of XAG-49 counter so tha...
Utsavi Avatar
Posted By Utsavi
Thu May 18 2017, 05:57 AM
HelloThanks for reply.No the input pin is not faul...
ExperimenterUK Avatar
Posted By ExperimenterUK
Wed May 17 2017, 07:38 PM
Just from reading the data sheet you seem to doing...
Utsavi Avatar
Posted By Utsavi
Wed May 17 2017, 11:01 AM
HelloI am working with PXAG49KBA. In my project I ...
Samimash Avatar
Posted By Samimash
Wed May 17 2017, 04:37 AM
thank you for your reply friend 'cc1' is a file ac...
ExperimenterUK Avatar
Posted By ExperimenterUK
Tue May 16 2017, 05:05 PM
I'm sure this is a compiler / Linux problem.In Lin...