Discussion in "General help Guidance and Discussion" started by    sherline123    Mar 6, 2016.
Sun Mar 06 2016, 12:38 PM
#1
Hi. I am new at here. I want to ask is it possible to burn/program EPROM by using 8051? The eprom that i wish to program is EPROM 27128. @@
Mon Mar 07 2016, 03:17 AM
#2
It has been years since I programmed eproms.

You will need to get the spec sheet from the maker, as not all 27128s are the same.
Most need a programming voltage of 12 volts or more.
The exact value varies.

You will need to make a programmer to drive the 27128 pins, both address and data.
Also you need to switch reset and Vpp (12v).

But yes , an 8051 could do most of the work.
You need a strong UV light source to erase the eprom.




[ Edited Mon Mar 07 2016, 03:18 AM ]
Tue Mar 08 2016, 03:26 AM
#3


It has been years since I programmed eproms.

You will need to get the spec sheet from the maker, as not all 27128s are the same.
Most need a programming voltage of 12 volts or more.
The exact value varies.

You will need to make a programmer to drive the 27128 pins, both address and data.
Also you need to switch reset and Vpp (12v).

But yes , an 8051 could do most of the work.
You need a strong UV light source to erase the eprom.



ExperimenterUK


thanks for the reply. sorry i am just a beginner. So i am going to use the eprom as the part of the memory of 8051 or i just use the 8051 GPIO to program it?
Tue Mar 08 2016, 03:56 AM
#4


thanks for the reply. sorry i am just a beginner. So i am going to use the eprom as the part of the memory of 8051 or i just use the 8051 GPIO to program it?

sherline123


I'm not sure what you mean.
The 8051 can use EPROMs such as the 27128 as external memory
but read only. (ROM)
To write to an EPROM takes extra hardware, a separate programmer.

One way would be..
Send a byte to the 8051 through the serial port.
Use the ports on the 8051 to set the address and
data pins of the 27128.
Use the remaining 8051 i/o pins to switch E,P and G.

Write the byte, then read it back.
When the byte is programmed,get the next.

Why are you programming a 27128 ?


[ Edited Fri Mar 11 2016, 04:06 AM ]

Get Social

Information

Powered by e107 Forum System

Conversation

Thu Nov 21 2019, 12:30 PM
raj2555
how to interface 8051 microcontroller with NRF24L01+ module
ExperimenterUK
Sat Oct 12 2019, 10:23 PM
Log in.. then post your code in the 8051 forum
Sat Oct 12 2019, 10:18 AM
Bhadra Sajikumar
i am doing a countdown timer with 8051 for my project, unfortunately our professor had to take a leave of absence before he could teach us most of it.. can someone explain the .asm code of it for me?
Mon Sep 23 2019, 07:37 AM
Nathaniel
I am doing a project for my schools wireless security system with cameras,sensors and spot lights using 8051 micro controller, could you help me out with the design and its source code.
Wed Sep 18 2019, 08:48 PM
Caryn Kover
Thank you for your time,
ExperimenterUK
Mon Aug 05 2019, 07:09 PM
@Ismail ..post in forum, give details
Mon Aug 05 2019, 04:33 PM
Ismail balghmi
Hello. Please I won't download
ExperimenterUK
Wed Jul 24 2019, 12:47 AM
@BUSTER123 Please post in the forum
Tue Jul 23 2019, 06:13 PM
BUSTER123
hello! newbie here. i am kind of a guy who hates using ready - made existing libraries, so this helped a lot as i was trying to control and write to a character lcd display. however, i can't figure out how to set the cursor position. for example, i want to set it to the 5th column in the first row, so position 5. so according to the table, i am sending 10000101 on the 8 data lines of the lcd (register select pulled low). the cursor does not move there however. and i cant move the cursor left or right too. is it something wrong that i am doing? thank you.
ExperimenterUK
Thu Jul 11 2019, 07:55 PM
@ramos https://www.theengineeringprojects.com/2017/09/l298-motor-driver-library-proteus.html

Downloads

Comments

ananyagupta
Tue Dec 03 2019, 07:53 AM
wells
Mon Nov 25 2019, 08:25 PM
auwal
Tue Nov 19 2019, 03:13 PM
ANKITPATEL
Mon Nov 18 2019, 11:00 AM
Casmir
Wed Nov 13 2019, 06:25 AM
DeepakBGattani
Mon Nov 11 2019, 01:31 PM
Jeanbusatta
Sun Nov 10 2019, 04:42 AM
mdayaz
Sat Nov 09 2019, 03:41 PM

Online

Guests: 38, Members: 0 ...

most ever online: 182184
(Members: , Guests: 182184) on 06 Aug 2010: 05:37 AM

Members: 38107
Newest member: ananyagupta
Forum Activity
ExperimenterUK Avatar
Posted By ExperimenterUK
Fri Nov 29 2019, 04:24 AM
" Is it possible to interface a fingerprint scanne...
ilylily07 Avatar
Posted By ilylily07
Thu Nov 28 2019, 03:50 PM
You will not find any code for an 8051 as no one w...
ExperimenterUK Avatar
Posted By ExperimenterUK
Tue Nov 26 2019, 05:44 PM
You will not find any code for an 8051 as no one w...
ilylily07 Avatar
Posted By ilylily07
Tue Nov 26 2019, 04:13 AM
I tracked down a OV7670 data sheet.The OV7670 puts...
ExperimenterUK Avatar
Posted By ExperimenterUK
Tue Nov 26 2019, 12:08 AM
I tracked down a OV7670 data sheet.The OV7670 puts...
ilylily07 Avatar
Posted By ilylily07
Mon Nov 25 2019, 04:38 PM
The 8051 has too little memory to do anything us...
ExperimenterUK Avatar
Posted By ExperimenterUK
Tue Nov 19 2019, 10:44 PM
The 8051 has too little memory to do anything us...
ilylily07 Avatar
Posted By ilylily07
Mon Nov 18 2019, 09:54 AM
0v7670 camera interfacing with stc 8051.using asse...
Jeanbusatta Avatar
Posted By Jeanbusatta
Sun Nov 10 2019, 04:43 AM
ty, really needed it
ExperimenterUK Avatar
Posted By ExperimenterUK
Tue Oct 22 2019, 05:18 AM