Discussion in "Electronics" started by    east    May 12, 2017.
Fri May 12 2017, 08:27 AM
#1
Hello~all,
Can you help me answer my doubts?
The sinusoidal signal in the simulated picture produced by ICL8038( This is the data-sheet of LCL8038: http://www.kynix.com/uploadfiles/pdf0125/ICL8038.pdf ) in the actual circuit. The another two resistances I used in actual circuit are Constantan resistances --10milliohm. However the wave which tested by the real oscilloscope is so mass and it’s so different from the effect of simulation.


Does anyone know what it occurred?


[ Edited Fri May 12 2017, 08:29 AM ]
Fri May 12 2017, 08:33 AM
#2
The picture is given below.




[ Edited Fri May 12 2017, 08:33 AM ]
Fri May 12 2017, 07:41 PM
#3
We really need to see your full actual circuit.
It occurs to me that a load of 20 milliohm would short out the signal.
In some case Proteus is more tolerant than the real thing,
and sometimes less tolerant.
What is the circuit for ?

Mon May 15 2017, 09:55 AM
#4
Hi, ExperimenterUK
I have found reason. When I used small resistance instead of big resistance,The driving ability to produce sine-wave of ICI8038 is not enough,so the wave is mass. After I decrease the sine wave amplitude, the wave is normal.
Thank you for you help.

Get Social

Information

Powered by e107 Forum System

Conversation

Mon May 08 2017, 12:45 PM
ivan muvunyi
please can you send me wiring diagram for automatic control of 3 phase induction motor for production of maize flour
Wed May 03 2017, 08:39 PM
imran qureshi
hello friend
Sun Apr 30 2017, 05:49 AM
Lijin G Varghese
Can u send me the circuit diagram for Program to interface GSM Module with 8051 microcontroller (AT89C51) using PC and LCD
Fri Apr 28 2017, 03:47 PM
SANDEEP T S
I need pcb wizard 3.5 version kindly send valid link of yours
ExperimenterUK
Mon Apr 17 2017, 11:56 PM
Sorry..We had a problem with registration.Confirmation emails were not sent.Please re-register
Thu Apr 13 2017, 07:29 PM
Piyush Aughad
I want circuit & program for radar detection using Microcontroller 8051
Tue Apr 11 2017, 03:27 AM
Shabbir Ahmed
Hi Ajay ....hope you and your family all will be fine are you working on andriod aplications if yes then plz reply me
Sun Apr 09 2017, 06:33 PM
ATHULYA NAIR
Dear Sir, I need to know what are the complexity for programming in 8051 Microcontroller for three phase inverter?
Sun Apr 09 2017, 06:32 PM
ATHULYA NAIR
Dear Sir,
Sun Apr 09 2017, 04:43 AM
Rohit chandra joshi
Sir I need ur help urgently.i am trying to make pc controlled led scrolling display using 8051.when i am trying to generate hex file of the code that is given by pratik suthar.it gives the error Target not created Limit:0800h I am using keil uvision4 software. Even i have tried to burn the given hex file that is atteched with the code but my led are not glowing. Pls help me sir .i struck in this problem from last month and till now i am not able to short out the problem. Pls suggest me to solve the problem.mail me at [email protected] Thanks

Downloads

Comments

Gaurav9527
Tue May 23 2017, 10:24 AM
rapushh
Tue May 23 2017, 10:22 AM
lubnakhan
Sat May 20 2017, 10:23 AM
Utsavi
Wed May 17 2017, 10:35 AM
Samimash
Tue May 16 2017, 01:15 PM
gangusa
Mon May 15 2017, 04:34 AM
raghuzala
Sun May 14 2017, 02:32 PM
Prakashlimbachiya
Sat May 13 2017, 07:34 AM

Online

Guests: 55, Members: 1 ...
rapushh viewing forum.php

most ever online: 182184
(Members: , Guests: 182184) on 06 Aug 2010: 05:37 AM

Members: 37829
Newest member: Gaurav9527
Forum Activity
rapushh Avatar
Posted By rapushh
Tue May 23 2017, 10:40 AM
Hi, I need to insert 3 mottorsteppers, along with ...
rapushh Avatar
Posted By rapushh
Tue May 23 2017, 10:28 AM
Hello my friends, I'm doing a 8051 project using A...
ajay_bhargav Avatar
Posted By ajay_bhargav
Fri May 19 2017, 10:17 AM
I think you are asking in the wrong forum. We do n...
ajay_bhargav Avatar
Posted By ajay_bhargav
Fri May 19 2017, 10:16 AM
You should start with something, We will help you ...
ajay_bhargav Avatar
Posted By ajay_bhargav
Fri May 19 2017, 07:01 AM
To me it looks like your development environment i...
ExperimenterUK Avatar
Posted By ExperimenterUK
Thu May 18 2017, 11:28 PM
Linux can be a minefield of make files, scripts an...
ExperimenterUK Avatar
Posted By ExperimenterUK
Thu May 18 2017, 11:18 PM
Can you provide me a demo of XAG-49 counter so tha...
Utsavi Avatar
Posted By Utsavi
Thu May 18 2017, 05:57 AM
HelloThanks for reply.No the input pin is not faul...
ExperimenterUK Avatar
Posted By ExperimenterUK
Wed May 17 2017, 07:38 PM
Just from reading the data sheet you seem to doing...
Utsavi Avatar
Posted By Utsavi
Wed May 17 2017, 11:01 AM
HelloI am working with PXAG49KBA. In my project I ...