Discussion in "Project Help" started by    kks    Mar 1, 2018.
Thu Mar 01 2018, 02:19 PM
#1
I posted a question before on the working of my project in Proteus. With the help from this website o successfully manged to run it on Proteus, but now when connecting the GND of motor driver ic to the GND of the 8051 programming board, the programming board doesn't even start. For better understanding (since the image its difficult to understand the connections) hers is the pins which i have connected to the 8051 programming board (i followed the proteus simulation circuit diagram which i am posting)

L293D MOTOR DRIVER IC :
A1 - P2.4
A2 - P2.5
EA - 5V
VCC - 12V
GND - GND

I also tried connecting the +ve to 12v and - ve to Gnd, still not working. Help me out here!


[ Edited Thu Mar 01 2018, 08:23 PM ]
Thu Mar 01 2018, 02:24 PM
#2
Here's the attached images.






#include<reg51.h>

#include<string.h>

#include<stdio.h>

#define lcdport P1


sbit rs=P3^7;
sbit en=P3^5;
sbit rw=P3^6;
sbit m1=P2^4;
sbit m2=P2^5;

char i,rx_data[50];

char rfid[13],ch=0;

char pass[4];

void forwardmotor(void) ;
void stopmotor(void);

 void delay(int itime)
{
    int i,j;
    for(i=0;i<itime;i++)
    for(j=0;j<1275;j++);
}

void daten()
{
    rs=1;
	  rw=0;
    en=1;
    delay(5);
    en=0;
}

void lcddata(unsigned char ch)
{
    lcdport=ch & 0xf0;
    daten();
    lcdport=(ch<<4) & 0xf0;
    daten();
}

void cmden(void)
{
    rs=0;
    en=1;
    delay(5);
    en=0;
}

void lcdcmd(unsigned char ch)
{
    lcdport=ch & 0xf0;
    cmden();
    lcdport=(ch<<4) & 0xf0;
    cmden();
}

void lcdstring(char *str)
{
    while(*str)
    {
        lcddata(*str);
        str++;
    }
}

void lcd_init(void)
{
    lcdcmd(0x02);
    lcdcmd(0x28);
    lcdcmd(0x0e);
    lcdcmd(0x01);
}

void uart_init()
{
 TMOD=0x20;
 SCON=0x50;
 TH1=0xfd;
 TR1=1;
}
char rxdata()
{
  while(!RI);
    ch=SBUF;    
    RI=0;
    return ch;
}

void forwardmotor()
{
  m1=1; 
	m2=0;    
	delay(500);
  stopmotor(); 
	delay(500);
  m1=0; 
	m2=1;    
	delay(500);   
	stopmotor();
}


void stopmotor()
{
  m1=0; 
	m2=0;
}

void main()
{
    uart_init();
    lcd_init();
    lcdstring("  RFID Based    ");
    lcdcmd(0xc0);
    lcdstring("Security system "); 
    delay(400);
    while(1)
    {
        lcdcmd(1);
        lcdstring("Place Your Card:");
        lcdcmd(0xc0);
        i=0;
        for(i=0;i<12;i++)
        rfid[i]=rxdata();
        rfid[i]='\0';
        lcdcmd(1);
        lcdstring("Your ID No. is:");
        lcdcmd(0xc0);
        for(i=0;i<12;i++)
        lcddata(rfid[i]);
        delay(100);
        if(strncmp(rfid,"160066A5EC39",12)==0)
        {
            lcdcmd(1);
            lcdstring("Access Granted ");
            lcdcmd(0xc0);
            lcdstring("Person1");
            forwardmotor();
          }
        
        else if(strncmp(rfid,"160066BD7AB7",12)==0)
            {
            lcdcmd(1);
            lcdstring("Access Granted ");
            lcdcmd(0xc0);
            lcdstring("Person2");
            m1=1;
            m2=0;
            delay(300);
            m1=0;
            m2=0;
            delay(200);
            m1=0;
            m2=1;
            delay(300);
            m1=0;
            m2=0;
            }
            
                else if(strncmp(rfid,"160066203060",12)==0)
            {
            lcdcmd(1);
            lcdstring("Access Granted ");
            lcdcmd(0xc0);
            lcdstring("Person3");
            m1=1;
            m2=0;
            delay(300);
            m1=0;
            m2=0;
            delay(200);
            m1=0;
            m2=1;
            delay(300);
            m1=0;
            m2=0;    
            }

        else 
        {
           lcdcmd(1);
           lcdstring("Access Denied");
           delay(300);
        }
  }
}


[ Edited Thu Mar 01 2018, 08:38 PM ]
Thu Mar 01 2018, 08:40 PM
#3
The motor driver module.

Thu Mar 01 2018, 09:31 PM
#4
EA is "Enable A".
It can be switched on and off by logic, or tied high, but not both.
Disconnect EA from pin P2.3 or the 5Volt supply.
If using P2.3 , set it high when the motor is running.


Vcc is 5 volts, by connecting to 12v you may have damaged the chip.
Worse, 12 volts may have fed back onto the main board and damaged it.

Supply the 12 volt power to the screw connections labelled + V -

Fri Mar 02 2018, 07:25 AM
#5
I don't know whether i damaged it or not. The board is behaving strangely though. Sometimes it works, sometimes it doesn't display anything on the Lcd with the same connections.
I have given both 5v and 12v both to vcc. I even tried giving 12v to the + V - pins. But whenever i try to give 12v to either vcc or - /+, the lcd brightens up a little more and the text that was appearing before disappears. Plus there is the problem with the Gnd connection. Doesn't matter what i do as soon as i connect the Gnd pin to the gnd of microcontroller, the board doesn't work. What should i do?
Fri Mar 02 2018, 08:27 PM
#6
The first thing is to check the microcontroller.
Disconnect the motor driver board completely.
Does the microcontroller board (the main board) work normally ?
Fri Mar 02 2018, 11:59 PM
#7
Yes it works fine enough. I have successfully managed to run the program without the motor driver module. When i give Gnd then on giving Vcc Lcd stops working and vice versa.
Sat Mar 03 2018, 10:13 PM
#8
It sounds very much like the driver module is damaged.
Replace the L293 chip.
Do not connect Vcc to 12 volt.
Sun Mar 04 2018, 02:20 AM
#9
😔 Guess you are right. Isn't there any other way in which i can run the motor?
Sun Mar 04 2018, 09:18 PM
#10


😔 Guess you are right. Isn't there any other way in which i can run the motor?

kks


As this is an academic project, do you really need a motor ?
Can you use another way to indicate a door being unlocked.. say an LED ?

Getting a motor to go one way then the other is quite difficult.
You can use relays,but I assume you don't have any.
The L293 chip is the simplest way.

How much current does your motor draw ?


Get Social

Information

Powered by e107 Forum System

Conversation

Sat Feb 01 2020, 10:12 AM
Pearl Olin
Hello,
Wed Jan 22 2020, 06:16 PM
MINU CHAUDHARY
I m getting errors while simulation process during interfacing socket output and lcd... Can i get the report of ur project which is same as us.
Tue Jan 14 2020, 07:08 AM
shubham kharade
when i am trying to simulate the program in Proteus 8 professional, I am getting some errors as cannot find module file dhtxx.md can u help me
Tue Dec 17 2019, 01:44 PM
Devangi
hello..i am programming industrial timer using 8051 with 24lc64 eeprom. i have query in storing the 3 diff value in eeprom with enter button. can anyone share c code ?
Tue Dec 17 2019, 10:30 AM
Andrius
Hello. Can anyone share the code in Bascon and scheme in Proteus?
Thu Nov 21 2019, 12:30 PM
raj2555
how to interface 8051 microcontroller with NRF24L01+ module
ExperimenterUK
Sat Oct 12 2019, 10:23 PM
Log in.. then post your code in the 8051 forum
Sat Oct 12 2019, 10:18 AM
Bhadra Sajikumar
i am doing a countdown timer with 8051 for my project, unfortunately our professor had to take a leave of absence before he could teach us most of it.. can someone explain the .asm code of it for me?
Mon Sep 23 2019, 07:37 AM
Nathaniel
I am doing a project for my schools wireless security system with cameras,sensors and spot lights using 8051 micro controller, could you help me out with the design and its source code.
Wed Sep 18 2019, 08:48 PM
Caryn Kover
Thank you for your time,

Downloads

Comments

arun.sapro
Wed Feb 12 2020, 04:47 PM
prathmiyer
Tue Feb 11 2020, 11:12 AM
Just4Fun
Sat Feb 01 2020, 01:29 PM
Deepkumar
Thu Jan 30 2020, 03:52 PM
wounder
Sat Jan 25 2020, 12:09 PM
brucewilliams20
Thu Jan 23 2020, 11:47 AM
Nippy56
Sun Jan 19 2020, 02:13 AM
usb5962
Sat Jan 11 2020, 10:42 AM

Online

Guests: 122, Members: 0 ...

most ever online: 182184
(Members: , Guests: 182184) on 06 Aug 2010: 05:37 AM

Members: 38122
Newest member: arun.sapro
Forum Activity
wounder Avatar
Posted By wounder
Mon Feb 10 2020, 08:32 AM
From below sample code for nuvoton 8051 timer0 mod...
Just4Fun Avatar
Posted By Just4Fun
Sat Feb 01 2020, 02:20 PM
If you want to use a CH55x MCU there isn't any adv...
Just4Fun Avatar
Posted By Just4Fun
Sat Feb 01 2020, 01:51 PM
Hi all,I was curious to try out the CH552 MCU (805...
Deepkumar Avatar
Posted By Deepkumar
Thu Jan 30 2020, 05:36 PM
I want to send a text message in other than the En...
ExperimenterUK Avatar
Posted By ExperimenterUK
Sun Jan 26 2020, 04:05 AM
For a 12MHz crystal using a normal divided by 12 c...
wounder Avatar
Posted By wounder
Sat Jan 25 2020, 12:14 PM
I have a 8051 micro controller ,it has timer0,1,2,...
ExperimenterUK Avatar
Posted By ExperimenterUK
Fri Jan 17 2020, 10:24 PM
We will need the circuit diagram.A Proteus simulat...
Billz Avatar
Posted By Billz
Sat Jan 11 2020, 05:43 PM
hi everyone please attached files are my c code fo...
ExperimenterUK Avatar
Posted By ExperimenterUK
Tue Jan 07 2020, 08:18 PM
Not a stupid question.Setting up "Eclipse" can be...
elt Avatar
Posted By elt
Tue Jan 07 2020, 07:06 PM
So i have just began learning programming micros a...