Discussion in "Project Help" started by    Pater    May 14, 2018.
Mon May 14 2018, 05:36 PM
#1
Basically my project is based on Data Acquisition system, so I want to acquire the data from various sensors in the PC.

For this i have used ADC0808 for converting Analog data to Digital data (8 bits), and these digital bits are given to any one port of micro-controller (89S52). The micro-controller then receives the bits and transmit it serially so that PC can receive the serial bits.

I have used "ADC0808 module with external clock" (By Silicon Technologies) :- attachment-1 &
"89S52 development board" (By Silicon Technologies) :- attachment-2

My code is as follows,
---------------------------------------------------------------------------------------------------------------------------
#include<reg51.h>

void delay_sec(unsigned int);
void delay_us(unsigned int);

void decimal();
void serial(char c);
unsigned char d1,d2,d3,d4;
void InitADC(void);
unsigned char ReadADC(unsigned char);

#define AN0 0
#define AN1 1
#define AN2 2
#define AN3 3

sbit Add_A = P2^0;
sbit Add_B = P2^1;
sbit Add_C = P2^2;
sbit ALE = P2^3;
sbit EOC = P2^4;
sbit OE = P2^5;
sbit START = P2^6;



#define Data_Bus P0
#define HalfCycleDelay 10 // usecs


void main()
{

unsigned char I;
InitADC();

while(1)
{
I= ReadADC(AN0);
}

}

void InitADC(void)
{
Add_A = 0;
Add_B = 0;
Add_C = 0;
ALE = 0;
EOC = 1;
OE = 0;
START = 0;

Data_Bus = 0xFF;
}

unsigned char ReadADC(unsigned char Channel)
{
unsigned int i = 0;
unsigned int ADC_value = 0;

/*Selecting analog Channel by providing respective
bits to A,B,C addresses*/
switch(Channel)
{
case AN0: Add_C = 0; Add_B = 0; Add_A = 0; break;

}

delay_us(HalfCycleDelay); // 250kHz Frequency
ALE = 1; // Enable Address Latch

delay_us(HalfCycleDelay); // 250kHz Frequency

START = 1; // Start ADC Conversion
delay_us(HalfCycleDelay); // 250kHz Frequency

ALE = 0; // Disable Address Latch
delay_us(HalfCycleDelay); // 250kHz Frequency

START = 0; // Complete the start pulse

for(i=0;i<2000;i++)
{

delay_us(HalfCycleDelay); // 250kHz Frequency
if(!EOC) // Wait for EOC to be low
break;
}

for(i=0;i<2000;i++)
{

delay_us(HalfCycleDelay); // 250kHz Frequency
if(EOC) // Wait for EOC to be High
break;
}


OE = 1; // Enable Output
delay_us(HalfCycleDelay); // 250kHz Frequency

delay_us(HalfCycleDelay); // 250kHz Frequency

delay_us(HalfCycleDelay); // 250kHz Frequency


ADC_value = Data_Bus; // Read value

decimal();
serial(d1+0x30);
serial(d4+0x30);
serial(d3+0x30);

delay_sec(1);

delay_us(HalfCycleDelay); // 250kHz Frequency
OE = 0; // Disable Output

delay_us(HalfCycleDelay); // 250kHz Frequency
return ADC_value; // Return ADC value
}


void decimal()
{

d1 = Data_Bus /100;
d2 = Data_Bus %100;
d3 = d2 %10;
d4 = d2/10;

}


void serial(char c)
{

TMOD = 0X20;
TH1 = 0XFD;
SCON = 0X50;
TR1 = 1;
SBUF = c;
while(TI==0);
TI = 0;

}

// Function for approximate delay in Secs.
void delay_sec(unsigned int d)
{
unsigned int i;
for(i=0;i<(d*20);i++)
delay_us(50000);
}

// Function for approximate delay in given uSecs.
void delay_us(unsigned int d)
{
unsigned int i, limit;
limit = d/15;
for(i=0;i<limit;i++);
}

----------------------------------------------------------------------------------------------------------------

So the main problem is that I am not getting Analog to Digital conversion on the port of micro-controller and also no data in the PC (Used hyper-terminal for getting serial data) & if getting, am getting any random data in the PC.

I have made all connections as per the code but it is not working.

So please help in this regard and give suitable solution regarding Hardware part or the Programming part.

Mon May 14 2018, 10:17 PM
#2


So the main problem is that I am not getting Analog to Digital conversion on the port of micro-controller and also no data in the PC (Used hyper-terminal for getting serial data) & if getting, am getting any random data in the PC.

Pater



You code works okay on Proteus.
Random values looks like wiring or power problems.

Where do you get your test input voltage ?

What happens if you connect ADC0809 IN0 directly to ground ?
What happens if you connect ADC0809 IN0 directly to +5volts ?


[ Edited Mon May 14 2018, 10:19 PM ]

Get Social

Information

Powered by e107 Forum System

Conversation

Thu Nov 21 2019, 12:30 PM
raj2555
how to interface 8051 microcontroller with NRF24L01+ module
ExperimenterUK
Sat Oct 12 2019, 10:23 PM
Log in.. then post your code in the 8051 forum
Sat Oct 12 2019, 10:18 AM
Bhadra Sajikumar
i am doing a countdown timer with 8051 for my project, unfortunately our professor had to take a leave of absence before he could teach us most of it.. can someone explain the .asm code of it for me?
Mon Sep 23 2019, 07:37 AM
Nathaniel
I am doing a project for my schools wireless security system with cameras,sensors and spot lights using 8051 micro controller, could you help me out with the design and its source code.
Wed Sep 18 2019, 08:48 PM
Caryn Kover
Thank you for your time,
ExperimenterUK
Mon Aug 05 2019, 07:09 PM
@Ismail ..post in forum, give details
Mon Aug 05 2019, 04:33 PM
Ismail balghmi
Hello. Please I won't download
ExperimenterUK
Wed Jul 24 2019, 12:47 AM
@BUSTER123 Please post in the forum
Tue Jul 23 2019, 06:13 PM
BUSTER123
hello! newbie here. i am kind of a guy who hates using ready - made existing libraries, so this helped a lot as i was trying to control and write to a character lcd display. however, i can't figure out how to set the cursor position. for example, i want to set it to the 5th column in the first row, so position 5. so according to the table, i am sending 10000101 on the 8 data lines of the lcd (register select pulled low). the cursor does not move there however. and i cant move the cursor left or right too. is it something wrong that i am doing? thank you.
ExperimenterUK
Thu Jul 11 2019, 07:55 PM
@ramos https://www.theengineeringprojects.com/2017/09/l298-motor-driver-library-proteus.html

Downloads

Comments

ananyagupta
Tue Dec 03 2019, 07:53 AM
wells
Mon Nov 25 2019, 08:25 PM
auwal
Tue Nov 19 2019, 03:13 PM
ANKITPATEL
Mon Nov 18 2019, 11:00 AM
Casmir
Wed Nov 13 2019, 06:25 AM
DeepakBGattani
Mon Nov 11 2019, 01:31 PM
Jeanbusatta
Sun Nov 10 2019, 04:42 AM
mdayaz
Sat Nov 09 2019, 03:41 PM

Online

Guests: 28, Members: 0 ...

most ever online: 182184
(Members: , Guests: 182184) on 06 Aug 2010: 05:37 AM

Members: 38107
Newest member: ananyagupta
Forum Activity
ExperimenterUK Avatar
Posted By ExperimenterUK
Fri Nov 29 2019, 04:24 AM
" Is it possible to interface a fingerprint scanne...
ilylily07 Avatar
Posted By ilylily07
Thu Nov 28 2019, 03:50 PM
You will not find any code for an 8051 as no one w...
ExperimenterUK Avatar
Posted By ExperimenterUK
Tue Nov 26 2019, 05:44 PM
You will not find any code for an 8051 as no one w...
ilylily07 Avatar
Posted By ilylily07
Tue Nov 26 2019, 04:13 AM
I tracked down a OV7670 data sheet.The OV7670 puts...
ExperimenterUK Avatar
Posted By ExperimenterUK
Tue Nov 26 2019, 12:08 AM
I tracked down a OV7670 data sheet.The OV7670 puts...
ilylily07 Avatar
Posted By ilylily07
Mon Nov 25 2019, 04:38 PM
The 8051 has too little memory to do anything us...
ExperimenterUK Avatar
Posted By ExperimenterUK
Tue Nov 19 2019, 10:44 PM
The 8051 has too little memory to do anything us...
ilylily07 Avatar
Posted By ilylily07
Mon Nov 18 2019, 09:54 AM
0v7670 camera interfacing with stc 8051.using asse...
Jeanbusatta Avatar
Posted By Jeanbusatta
Sun Nov 10 2019, 04:43 AM
ty, really needed it
ExperimenterUK Avatar
Posted By ExperimenterUK
Tue Oct 22 2019, 05:18 AM