Now you can test GreenBee project before you make it on hardware. Author M.Mohsin who has sucessfully completed GreenBee project had first tested this on proteus before going to real hardware. And test came positive

You can also give a try to this simulation project. Please not the following:

1. Simulation project can only be run on Proteus 7.4 SP3 or higher (you may still give it a try and update me if it works)

2. You need to generate hex file yourself (download codes from download section.

Here are some tips from M.Mohsin (good one):

TIPS FOR THOSE WHO ARE WILLING TO DO THIS PROJECT

Hello Guys!

Since i have completed this project successfully, so i am in a good position to give you some tips that will help you for completing this project


1: Start the project as early as possible before your deadline.
2: Before starting the project you must make a roadmap of your work i-e How and from where to start the project.
3: Make sure before starting that all the components are available in your local market.
4: Never start the project directly on hardware. You must first design and check the simulation of your circuit on a simulation software. I will adivse to go for PROTEUS. This is the most user friendly and easy software to use for simulation purpose.
5: Start with the sensors. First make the sensors. After completing each sensor check and confirm its output. The readings table are given in the report. Your output voltages can be confirmed by that tables.
6: Never assume that you can complete your project by only going through the given report. You will never be able to do that. There are many bugs and errors in the report. You will have to workout alot yourself and find those errors.
7: You will face a lot of problems while making this project. Dont panic at any stage. All the problems will be much easier to solve once you get deeper into the project.
8: Dont try to complicate your circuit because it will cause you problems in troubleshooting. Try to make your each circuit as simple as you can with least number of wires. Make sure you make tight connections (specially for LCD).
9: Always use male and female connectors where ever required. It will make your job eazy since you will require to unplug your certain connections at regular intervals of time.
10: Be careful while solding the Relay and Actuator circuit. A small error in your connections can cost you a big deal.

Stay calm while doing this project:)
If you face any problem feel free to as on the FORUM
Many intelligent people are there to help you!

Regards
Engr M.Mohsin

M.Mohsin



A Screenshot of Mohsin\'s complete finished hardware



Please use forum for any help needed!
Tags Greenbee simulationproteus simulation greenbeeMonitor and Control of Greenhouse Environment-Gree
printer friendly create pdf of this news item

Comments

jaber
22 Dec 2014: 14:37 PM
i need the Hex file please
  

Submit comment

(Required; Min length 5)
(Required; will not be displayed)

Conversation

Wed Jun 03 2020, 05:21 AM
Katherine Hoag
No cost advertising for your website here: https://bit.ly/freeadsubmission
scena
Tue May 19 2020, 06:29 PM
Does anyone have microcontroller programming software for STC15F104W (core 8051, 4 k, 128 byte, 6 I/O pin, UART ... DIL8), that works?
Sat May 02 2020, 03:38 PM
Tamu Gurung
Hi I am looking for a assembly language program for a digital decimal counter. Time counts max limit of 2 mins starting from 2.00 mins and ending at 0.00. time is to be displayed on 4 7-segment LED displays. Edsim51 simulator to be used. Thanks
Wed Mar 25 2020, 09:39 AM
Tajammul
Sir kindly send the code file i2c for 8051
ExperimenterUK
Fri Mar 13 2020, 06:36 PM
@ Rohitnani,ABEBE..which project ?
Fri Mar 13 2020, 08:55 AM
ABEBE
how can get hadwere of this project
Rohitnani
Sat Mar 07 2020, 12:11 PM
Sir, Could you please send me the zip file input password....
Wed Feb 26 2020, 11:58 AM
Peter Parker
Is it possible to send multiple messages using only 1 GSM module?
Sat Feb 01 2020, 05:12 AM
Pearl Olin
Hello,
Wed Jan 22 2020, 01:16 PM
MINU CHAUDHARY
I m getting errors while simulation process during interfacing socket output and lcd... Can i get the report of ur project which is same as us.

Downloads

Comments

Davidthils
Thu May 21 2020, 08:44 AM
Jakeror
Wed May 20 2020, 09:28 PM
motorCar
Wed May 20 2020, 03:05 PM
Vordrync
Wed May 20 2020, 07:52 AM
JadenjiT
Wed May 20 2020, 03:15 AM
scena
Tue May 19 2020, 06:08 PM
CodySiz
Tue May 19 2020, 02:22 PM
ClaireSat
Mon May 18 2020, 09:50 PM

Online

Guests: 128, Members: 0 ...

most ever online: 182184
(Members: , Guests: 182184) on 06 Aug 2010: 01:37 AM

Members: 38211
Newest member: Davidthils
Forum Activity
xrxx Avatar
Posted By xrxx
Thu Apr 30 2020, 06:59 AM
BCD MULTIPLICATIONAssume that you have to 2 BCD nu...
liqian Avatar
Posted By liqian
Tue Apr 28 2020, 05:26 AM
I happened to see your post and I got many useful ...
ExperimenterUK Avatar
Posted By ExperimenterUK
Tue Apr 28 2020, 04:21 AM
The code is hard to read.Please zip it and attach ...
rogermado Avatar
Posted By rogermado
Sun Apr 26 2020, 01:53 AM
@ExperimenterUK, thanks for your reply. You'll fin...
ExperimenterUK Avatar
Posted By ExperimenterUK
Sat Apr 25 2020, 05:42 PM
Some simulators handle displays better than others...
rogermado Avatar
Posted By rogermado
Sat Apr 25 2020, 03:59 PM
Hello everyone, sorry in advance if i'm not in the...
PHANTOM28 Avatar
Posted By PHANTOM28
Fri Feb 28 2020, 10:25 AM
Hi.I hope you all can help me. I am relatively ne...
ExperimenterUK Avatar
Posted By ExperimenterUK
Fri Feb 21 2020, 05:05 PM
ajay_bhargav Avatar
Posted By ajay_bhargav
Fri Feb 21 2020, 04:45 AM
Yes you can do that.1. Create a channel @Thingspea...
ananyagupta Avatar
Posted By ananyagupta
Thu Feb 20 2020, 03:58 AM
With regards to the particular characters sent to ...