Bluetooth (UART) Programming in C
Discussion in "Project Doubts" started by Otto Mar 26, 2012.
Mon Mar 26 2012, 02:25 pm
Hello all,
In past i got much help from this site today again i need some help from u guys.
My new project is on Bluetooth programming, for that i have "Bluecontrol Evalution board with Bluecontrol". See it from this link.
http://www.blueserial.de/pdf/BlueControl_Datasheet.pdf
I had connect this Eval-board with RS232 to my PC (COM3-SPP Slave, COM5-BS config). So for Teraterm connection i m using COM3.
Another i have "Bluetooth USB Dongle".This i had also connected with my PC bcoz to give Bluetooth to my PC. See it from this link.
http://www.conrad.de/technik/bluetooth-usb-dongle.html
The task is i send one message like "Hello" from Bluecontrol to my PC (via Bluetooth). how can i do this? If anyone know then pls tell me the possible ways to perform this task.
I m working with Win-7. & i have TeraTerm for Terminal.
I had experience for microcontroller programming, but first time i m doing Bluetooth programming, so may be i m going in wrong way.pls suggest me for this. I had read much in Internet, but still not getting the perfect way to go furture.
pls share ur ideas and suggestions for fulfil this task.
Another question is I have BT Module HC-05. I m searching for Evaluation Board for this.
If anyone koow then pls reply me
thanks in advance.
Otto
In past i got much help from this site today again i need some help from u guys.
My new project is on Bluetooth programming, for that i have "Bluecontrol Evalution board with Bluecontrol". See it from this link.
http://www.blueserial.de/pdf/BlueControl_Datasheet.pdf
I had connect this Eval-board with RS232 to my PC (COM3-SPP Slave, COM5-BS config). So for Teraterm connection i m using COM3.
Another i have "Bluetooth USB Dongle".This i had also connected with my PC bcoz to give Bluetooth to my PC. See it from this link.
http://www.conrad.de/technik/bluetooth-usb-dongle.html
The task is i send one message like "Hello" from Bluecontrol to my PC (via Bluetooth). how can i do this? If anyone know then pls tell me the possible ways to perform this task.
I m working with Win-7. & i have TeraTerm for Terminal.
I had experience for microcontroller programming, but first time i m doing Bluetooth programming, so may be i m going in wrong way.pls suggest me for this. I had read much in Internet, but still not getting the perfect way to go furture.
pls share ur ideas and suggestions for fulfil this task.
Another question is I have BT Module HC-05. I m searching for Evaluation Board for this.
If anyone koow then pls reply me
thanks in advance.
Otto
[ Edited Wed Mar 28 2012, 06:19 pm ]
Tue Mar 27 2012, 02:19 am
Otto, sending file over bluetooth means you are using OBEX profile. Please make sure what bluetooth profiles are supported by this BT Module HC-05. I am really doubtful if this service is supported.
Tue Mar 27 2012, 01:39 pm
hello ajay, thanks for reply. But i don't know how to programming OBEX?
i know what is OBEX, but programming is bit tought for me.
I must need AT command or without AT command possible to programmingbluetooth ?
I want to tell u correction that my task is to send message e.g "Hello" from controller to PC, not file. pls help me for this.
i know what is OBEX, but programming is bit tought for me.
I must need AT command or without AT command possible to programmingbluetooth ?
I want to tell u correction that my task is to send message e.g "Hello" from controller to PC, not file. pls help me for this.
[ Edited Wed Mar 28 2012, 06:19 pm ]
Sat Mar 31 2012, 01:23 am
for this i think there is BT uart facility or feature thats available with all the BT modules. You will get a serial port on ur PC it will be same as sending data over serial. You must check your BT datasheet for more information.
Mon Apr 02 2012, 04:45 pm
hello ajay,
i know that one can send data from BT to PC throught RS-232 UART. I had connect the Evaluation board to PC with RS232 & set all necessary configuration, but the problem is i don't get any response from controller, after writting AT commands.
I set the Baudrate as per Datasheet, still don't get any response.
Need i SPP Slave or BS Config for communication?
i know that one can send data from BT to PC throught RS-232 UART. I had connect the Evaluation board to PC with RS232 & set all necessary configuration, but the problem is i don't get any response from controller, after writting AT commands.
I set the Baudrate as per Datasheet, still don't get any response.
Need i SPP Slave or BS Config for communication?
[ Edited Mon Apr 02 2012, 04:46 pm ]
Tue Apr 10 2012, 12:01 am
Hi Otto, I lost many forum posts coz of server move. Please check your email for my reply.
Wed Feb 06 2013, 03:50 pm
hello everybody
I am working on Bluetooth based project in which i want to transmit text file from sd card on micro controller to PC over Bluetooth. i have programmed AVR controller for SPP profile where i receive string on Hyper terminal. but i don't know how to transmit file from controller to PC over Bluetooth. i think i have to use OBEX profile. please some one light on my way and help me to complete this project
I am working on Bluetooth based project in which i want to transmit text file from sd card on micro controller to PC over Bluetooth. i have programmed AVR controller for SPP profile where i receive string on Hyper terminal. but i don't know how to transmit file from controller to PC over Bluetooth. i think i have to use OBEX profile. please some one light on my way and help me to complete this project
Thu Feb 07 2013, 12:01 am
taher, Please create a new thread for your problem. Its not advisable to post in old threads.
Powered by e107 Forum System