Discussion in "Project Doubts" started by    LAMBO    Apr 12, 2018.
Tue May 01 2018, 11:56 AM
#11
Hi sir
Sorry it wasn't moc2021 it was moc3021 as u told to change an ac fan with a 100watt bulb but sir 460ohm resistance got burned out and sir i replaced 460 ohm with 1k than also it burned out and in snubber circuit I kept value of R as 47 ohm and C as 103/1kv

Tue May 01 2018, 06:10 PM
#12
It still looks like a faulty triac or a wiring error.

Remove all components but the triac.
Connect one side of the bulb to pin 2 (T2) and the other side to mains live.
Connect pin 1 (T1) to mains neutral.
Leave pin 3 (GATE) not connected.
The bulb should be off.

Then connect a resistor ( 100- 500 ohms) between pin 2 and pin 3.
The bulb should be on,with nothing burning.


Wed May 02 2018, 10:53 AM
#13
Hi sir
did the changes as per instructions. The circuitry is fine as per the burning is concerned. No heating is observed. But the speed of the fan is not changing. It gets speed up at particular level with pulsations in its speed. Is there any frequency that we should get at the output of zero detector circuit?

And sir i have uploaded a link related to mine project

https://drive.google.com/file/d/10ZL0QJLJ_S39kIiW4YF_B_9VsgqQZEdt/view?usp=drivesdk



Wed May 02 2018, 08:28 PM
#14
Thanks for the video clip, it's a good idea.

Electric motors vary a lot in how they work and are no good for testing.
Use a light bulb.

When fault finding it is important to take one step at a time.
Please follow these steps and tell me what happened.

Using a light bulb, does vary properly ?

If not...

Remove all components but the triac.
Connect one side of the bulb to pin 2 (T2) and the other side to mains live.
Connect pin 1 (T1) to mains neutral.
Leave pin 3 (GATE) not connected.
The bulb should be off is it ?

Then connect a resistor ( 100- 500 ohms) between pin 2 and pin 3.
The bulb should be on full power ,with nothing burning is it ?
Thu May 03 2018, 08:04 AM
#15
Hi sir
as u mentioned above everthing is working after that what should i do ??????
Thu May 03 2018, 03:32 PM
#16
If the circuit works with a light bulb, the problem may be the motor.
This controller is good for series motors, with brushes( small hand tools), not induction motors.

Reconnect the snubber across the triac.
Try other motors.
Sun May 13 2018, 02:13 PM
#17
Hi sir
after checking all the connection i connected the board to supply the bulb get directly on and it shows little flickring when we go to level 7-8 in bargraph led

after that i change old optocoupler(moc3021) from the new one(moc3021) and again connected to supply now the bulb won't get directly on but sir it neither gets on when we press the increment / decrement switch

sir what should i do ????

and sir can u let me know what should be an current in MA's output on load side
Mon May 14 2018, 09:40 PM
#18


Hi sir
after checking all the connection i connected the board to supply the bulb get directly on and it shows little flickring when we go to level 7-8 in bargraph led

LAMBO



I'm not sure what you are saying here.
Can you do another video ?
Sat Jun 16 2018, 07:15 AM
#19
hi sir
sorry for the late reply
sir can we control bulb by using this circuit through pot yes or no ????

Sat Jun 16 2018, 11:33 PM
#20


hi sir
sorry for the late reply
sir can we control bulb by using this circuit through pot yes or no ????



LAMBO


No.

Get Social

Information

Powered by e107 Forum System

Conversation

Fri Aug 07 2020, 08:01 AM
Tony Eldredge
{{Are You interested|Interested|Would you be interested} in {advertising|an advertising service} that {costs|charges} less than {$50|$40|$49|$39} {per month|monthly|every month} and {delivers|sends} {hundreds|thousands|tons} of people who are ready to buy directly to your website? {Check out|Visit|Have a look at|For details visit}: http://www.getwebsitevisitors.xyz |{Looking for fresh buyers?|Want more visitors for your website?|Do you want more people to visit your website?} {Get|Receive} {hundreds|thousands|tons} {of people who are ready to buy sent directly to your website|of keyword targeted visitors directly to your site}. {Boost your profits|Boost revenues} {fast|quick|super fast}. Start seeing results in as little as 48 hours. {For more info|To get details|For additional information|To get info} {Check out|Visit|Have a look at}: http://www.getwebsitevisitors.xyz
Thu Jun 11 2020, 06:27 AM
anudee
sir could please send the code for I2C and wifi interfacing with 8051
scena
Tue May 19 2020, 10:29 PM
Does anyone have microcontroller programming software for STC15F104W (core 8051, 4 k, 128 byte, 6 I/O pin, UART ... DIL8), that works?
Sat May 02 2020, 07:38 PM
Tamu Gurung
Hi I am looking for a assembly language program for a digital decimal counter. Time counts max limit of 2 mins starting from 2.00 mins and ending at 0.00. time is to be displayed on 4 7-segment LED displays. Edsim51 simulator to be used. Thanks
Wed Mar 25 2020, 01:39 PM
Tajammul
Sir kindly send the code file i2c for 8051
ExperimenterUK
Fri Mar 13 2020, 10:36 PM
@ Rohitnani,ABEBE..which project ?
Fri Mar 13 2020, 12:55 PM
ABEBE
how can get hadwere of this project
Rohitnani
Sat Mar 07 2020, 05:11 PM
Sir, Could you please send me the zip file input password....
Wed Feb 26 2020, 04:58 PM
Peter Parker
Is it possible to send multiple messages using only 1 GSM module?
Sat Feb 01 2020, 10:12 AM
Pearl Olin
Hello,

Downloads

Comments

Mirza123
Thu Jun 25 2020, 03:46 PM
eunicelove124
Mon Jun 22 2020, 03:03 PM
cerouno
Tue Jun 16 2020, 05:10 PM
Marce
Sat Jun 13 2020, 09:43 PM
Davidthils
Thu May 21 2020, 12:44 PM
Jakeror
Thu May 21 2020, 01:28 AM
motorCar
Wed May 20 2020, 07:05 PM
Vordrync
Wed May 20 2020, 11:52 AM

Online

Guests: 117, Members: 0 ...

most ever online: 182184
(Members: , Guests: 182184) on 06 Aug 2010: 05:37 AM

Members: 38215
Newest member: Mirza123
Forum Activity
liqian Avatar
Posted By liqian
Fri Aug 07 2020, 03:31 AM
I found the part on here https://www.jotrin.com/pr...
ExperimenterUK Avatar
Posted By ExperimenterUK
Wed Jul 01 2020, 11:07 PM
PS: I am a new learner thats why my question may s...
Mirza123 Avatar
Posted By Mirza123
Wed Jul 01 2020, 02:05 PM
Thanks for the assistance. I have read the data sh...
ExperimenterUK Avatar
Posted By ExperimenterUK
Wed Jul 01 2020, 10:12 AM
See section 15 (Ports) of the data sheet. ...
wimac Avatar
Posted By wimac
Tue Jun 30 2020, 10:05 AM
How did you know that it is not 8051. Mirza123It i...
Mirza123 Avatar
Posted By Mirza123
Tue Jun 30 2020, 08:39 AM
It seems ports on the AT89LP2052 is not like on th...
ExperimenterUK Avatar
Posted By ExperimenterUK
Tue Jun 30 2020, 08:34 AM
It seems ports on the AT89LP2052 are not like on t...
Mirza123 Avatar
Posted By Mirza123
Thu Jun 25 2020, 04:07 PM
Hello!i am trying to use AT89LP2052 ( AT89LP2052 h...
ExperimenterUK Avatar
Posted By ExperimenterUK
Wed Jun 17 2020, 09:42 PM
It is about capacitor? i should put it between Vcc...
cerouno Avatar
Posted By cerouno
Wed Jun 17 2020, 10:37 AM
Take another look at the power supply to the LCD.A...