Discussion in "Project Help" started by    ronotsig    May 27, 2019.
Mon May 27 2019, 03:06 AM
#1
I am trying to using P89LPC921 or P89LPC922 in a project. I cannot get the KBI function to work. It appears that I an unable to write KBPATN, KBMask, and KBCon. They only have default values. If I load the same small test program in the P89LPC925 it works flawlessly.
Does anyone with experience with the P89LPC92x processors successfully used the KBI function?
Mon May 27 2019, 06:23 PM
#2
I can't see any reason that those registers would be "Read only".
Are you sure you are using the correct header files ?

Which compiler are you using ?

Please zip and post your test code.


[ Edited Tue May 28 2019, 12:16 AM ]
Wed May 29 2019, 03:13 PM
#3
Since the code works for the P89LPC925, it is apparent that the registers are write/read. However it appears that the registers cannot be written in the 920/921.
Thank you for your response.

I have enclosed a schematic and my code. This is the circuitry for a speed sensor. A change of the port pin (hall effect sensor input) triggers an ISR to capture the time between pulses and compute rpm. The complete program works fine with a P89LPC925 but does not work in the P89LPC920 or P89LPC921. I would like to use the latter and you have 15000+ pieces in stock, but I have to get it to work. I only have one of the 920 and a few of the 921.

The date code of the 920 is “Yn6607B”.
The date code of the 921’s is “Yn6624B”

I do not have an emulator. The program is in assembly. (I have coded extensively in assembly for 40+ years.) I reduced the program functionality to an absolute minimum. No ISR for the Port0 pin. At its simplest it does the following:
- Read in ID.
- Write B0 of ID to NLEDRX.
- Write ID to KBPATN or KBMASK.
- Read KBPATN or KBMASK into ACC.
- Write B0 of ACC to NLEDTX.

The code runs fine on the 925 but not on the 920 or 921. The values read back from KBPATN and KBMASK are the initial values from RESET.

Do you know anyone who has? Do you have a contact who was an FAE with NXP or something.

I am in dire straights. I tested the program using the 925 part. Then for production run of 3000 units, I substituted the 921 part. Then I found out that the KBI function is not working in the 921 part (and also it does not work in the 920 part).

NXP does not care since they have discontinued the part. It is very frustrating. There must still be very knowledgeable people who would know of this problem and/or how it can be worked around. After all, how can you have a functionality in the datasheet and user manual that does not work. And especially since the 925 part is built on the same core with just additional peripherals.

Thanking you in advance.

Wed May 29 2019, 09:05 PM
#4
I would suggest a fresh approach.

The Keil compiler supports the P89LPC921,
so I would write a new mini test program in 'c'.

The Keil compiler is free for code under 2k.





[ Edited Thu May 30 2019, 04:20 AM ]
Thu May 30 2019, 08:32 PM
#5
It occurs to me that although the P89LPC921 and P89LPC925
are very similar, they are not the same.
Perhaps a careful look at the differences will give you the answer.

Get Social

Information

Powered by e107 Forum System

Conversation

Thu Jun 11 2020, 06:27 AM
anudee
sir could please send the code for I2C and wifi interfacing with 8051
scena
Tue May 19 2020, 10:29 PM
Does anyone have microcontroller programming software for STC15F104W (core 8051, 4 k, 128 byte, 6 I/O pin, UART ... DIL8), that works?
Sat May 02 2020, 07:38 PM
Tamu Gurung
Hi I am looking for a assembly language program for a digital decimal counter. Time counts max limit of 2 mins starting from 2.00 mins and ending at 0.00. time is to be displayed on 4 7-segment LED displays. Edsim51 simulator to be used. Thanks
Wed Mar 25 2020, 01:39 PM
Tajammul
Sir kindly send the code file i2c for 8051
ExperimenterUK
Fri Mar 13 2020, 10:36 PM
@ Rohitnani,ABEBE..which project ?
Fri Mar 13 2020, 12:55 PM
ABEBE
how can get hadwere of this project
Rohitnani
Sat Mar 07 2020, 05:11 PM
Sir, Could you please send me the zip file input password....
Wed Feb 26 2020, 04:58 PM
Peter Parker
Is it possible to send multiple messages using only 1 GSM module?
Sat Feb 01 2020, 10:12 AM
Pearl Olin
Hello,
Wed Jan 22 2020, 06:16 PM
MINU CHAUDHARY
I m getting errors while simulation process during interfacing socket output and lcd... Can i get the report of ur project which is same as us.

Downloads

Comments

Mirza123
Thu Jun 25 2020, 03:46 PM
eunicelove124
Mon Jun 22 2020, 03:03 PM
cerouno
Tue Jun 16 2020, 05:10 PM
Marce
Sat Jun 13 2020, 09:43 PM
Davidthils
Thu May 21 2020, 12:44 PM
Jakeror
Thu May 21 2020, 01:28 AM
motorCar
Wed May 20 2020, 07:05 PM
Vordrync
Wed May 20 2020, 11:52 AM

Online

Guests: 37, Members: 0 ...

most ever online: 182184
(Members: , Guests: 182184) on 06 Aug 2010: 05:37 AM

Members: 38215
Newest member: Mirza123
Forum Activity
ExperimenterUK Avatar
Posted By ExperimenterUK
Wed Jul 01 2020, 11:07 PM
PS: I am a new learner thats why my question may s...
Mirza123 Avatar
Posted By Mirza123
Wed Jul 01 2020, 02:05 PM
Thanks for the assistance. I have read the data sh...
ExperimenterUK Avatar
Posted By ExperimenterUK
Wed Jul 01 2020, 10:12 AM
See section 15 (Ports) of the data sheet. ...
wimac Avatar
Posted By wimac
Tue Jun 30 2020, 10:05 AM
How did you know that it is not 8051. Mirza123It i...
Mirza123 Avatar
Posted By Mirza123
Tue Jun 30 2020, 08:39 AM
It seems ports on the AT89LP2052 is not like on th...
ExperimenterUK Avatar
Posted By ExperimenterUK
Tue Jun 30 2020, 08:34 AM
It seems ports on the AT89LP2052 are not like on t...
Mirza123 Avatar
Posted By Mirza123
Thu Jun 25 2020, 04:07 PM
Hello!i am trying to use AT89LP2052 ( AT89LP2052 h...
ExperimenterUK Avatar
Posted By ExperimenterUK
Wed Jun 17 2020, 09:42 PM
It is about capacitor? i should put it between Vcc...
cerouno Avatar
Posted By cerouno
Wed Jun 17 2020, 10:37 AM
Take another look at the power supply to the LCD.A...
ExperimenterUK Avatar
Posted By ExperimenterUK
Wed Jun 17 2020, 02:01 AM
Take another look at the power supply to the LCD.A...