Frequency conversion?

Ahh good point on the external interrupt - just didn't think that thought to an end
There is absolutely no need to run an interrupt handler every single time.

I'l look at that diode - I guess it's better than using a resistor?... Read Compelte post
Other Tags: resistor   diode   
Posted by TB on Sat Aug 09 2008, 06:03 PM

MAX192 ADC schematics?

Fig 18 in the datasheet shows just that.
In general you can directly connect VDD,unless the supply is very noisy,in which case use a 10ohms resistor(which forms a low pass in conjunction with the bypass caps) as specified in the datasheet.
Usually a 0.1uF bypass cap from VDD to Agnd pin(as close to the pins as possible) suffices.... Read Compelte post
Other Tags: datasheet   resistor   pins   conjunction   
Posted by sashijoseph on Sun Aug 10 2008, 04:35 AM

component trouble

k thanx man, so any idea how i could go about making this substitute for the resistor array??... Read Compelte post
Other Tags: thanx man   resistor   array   
Posted by Ved on Sat Aug 09 2008, 05:44 PM

component trouble

hi ved,
if the resistor array in question is being used for pullups of the uC then the SIP used is internally connected as shown in figure. U can create ur own SIP using individual resistors of the same value in a similar configuration.





oops , looks like sunrom and i posted at the same time. ... Read Compelte post
Other Tags: pullups   resistors   resistor   sip   sunrom   
Posted by pdi33 on Sat Aug 09 2008, 07:30 PM

component trouble

Hey guys im making a pcb n cant get some of the parts at the shops in the city, a resistor array & ZIF sockets.... is there any substitute for the resistor array? & can i use a normal ic base instead of the zif socket... the pcb is that of a programmer board of some atmel microcontrollers... Read Compelte post
Posted by Ved on Sat Aug 09 2008, 02:15 PM

Conversation

ExperimenterUK
Thu Jul 11 2019, 07:55 PM
@ramos https://www.theengineeringprojects.com/2017/09/l298-motor-driver-library-proteus.html
ExperimenterUK
Thu Jul 11 2019, 07:44 PM
@praveen123. Can you give a link to the project ?
Thu Jul 11 2019, 04:47 PM
ramos
buenos dias alguien podria ayudarme necesito saber como descargar la libreria del l298n para proteus
Thu Jul 11 2019, 11:11 AM
praveen123
anyone can help me
Thu Jul 11 2019, 11:11 AM
praveen123
i need source code for 8051 -smart trolley rfid
Thu Jul 11 2019, 11:10 AM
praveen123
hii
ExperimenterUK
Thu Jun 27 2019, 09:14 PM
Hi.. good to see you again
۞ TPS ۞
Thu Jun 27 2019, 07:31 AM
Hello
AdiGhazi
Tue Jun 18 2019, 11:21 AM
Hlo Dear , I've to program AT89C51AC3 RT-LUM using flip but I'm getting time out error for RS232. Will you please suggest me which programmer will be supportable to program this Chip.
Sun Jun 16 2019, 07:48 PM
hanoch Taub
i need to interface sim800 to 8051, the problem is that on the module sim800 there are 9 pins connector and I don't know how to connect him to 8051, which pins to tx and rx on 8051 module sim there is

Downloads

Comments

zxcvbnm1234
Sat Jul 13 2019, 07:09 AM
surajghayal
Wed Jul 10 2019, 01:17 PM
figureyang
Fri Jul 05 2019, 04:25 AM
mousompal
Sat Jun 29 2019, 05:02 PM
AdiGhazi
Tue Jun 18 2019, 11:15 AM
Easwaran22
Thu Jun 13 2019, 10:16 AM
JenniferJJ
Thu Jun 13 2019, 05:12 AM
seyoonnet
Tue Jun 04 2019, 12:37 PM

Online

Guests: 39, Members: 0 ...

most ever online: 182184
(Members: , Guests: 182184) on 06 Aug 2010: 05:37 AM

Members: 38077
Newest member: zxcvbnm1234
Forum Activity
figureyang Avatar
Posted By figureyang
Fri Jul 05 2019, 04:37 AM
here is the source code prepared for you download ...
figureyang Avatar
Posted By figureyang
Fri Jul 05 2019, 04:30 AM
Cheap_Flash_FS(Normal Version)--Embedded FAT16/32 ...
wimac Avatar
Posted By wimac
Sat Jun 22 2019, 01:26 PM
I’ve use the AT89C51ED2 which has a similar progra...
ExperimenterUK Avatar
Posted By ExperimenterUK
Thu Jun 20 2019, 10:08 PM
baud rate is 9600 at stop bits of 2. AdiGhaziThe u...
AdiGhazi Avatar
Posted By AdiGhazi
Thu Jun 20 2019, 05:24 AM
Dear,I'm using RS232 serial port cable to use flip...
ExperimenterUK Avatar
Posted By ExperimenterUK
Tue Jun 18 2019, 10:19 PM
Okay.. I have never programmed the AT89C51AC3 or ...
AdiGhazi Avatar
Posted By AdiGhazi
Tue Jun 18 2019, 11:20 AM
Hlo Dear ,I've to program AT89C51AC3 RT-LUM using ...
ExperimenterUK Avatar
Posted By ExperimenterUK
Thu May 30 2019, 08:32 PM
It occurs to me that although the P89LPC921 and P8...
ExperimenterUK Avatar
Posted By ExperimenterUK
Wed May 29 2019, 09:05 PM
I would suggest a fresh approach.The Keil compile...
ronotsig Avatar
Posted By ronotsig
Wed May 29 2019, 03:13 PM
Since the code works for the P89LPC925, it is appa...