Discussion in "PIC Microcontroller Discussion" started by    Zacky    Mar 22, 2009.
Sun Mar 22 2009, 09:33 PM
#1
I managed to interface PC and PIC via USART. Now I want to interface both the PC and PIC via wireless using RF module. I got the 433MHz module from cytron.com. The PIC is supposed to report back to PC on its Port status via transmitter module which is connected to the TX of the PIC. The receiver module is connected to RX of PC. However, things are not working as they should. I used mikroBasic software to program my PIC. Using the built-in "connection terminal", I noticed that PC is picking up unwanted signals. How can I stop the PC from picking the unwanted signal? I'm cracking my head for the past 1week trying all sorts of programming method to filter it. Nothing seems to work. Help me please!
Sun Mar 22 2009, 11:53 PM
#2
What do you mean by "unwanted signals" ?
Mon Mar 23 2009, 03:52 AM
#3
which chip u r using.....how u interface pic and pc serially and what data u want to transfer from pic to pc
Mon Mar 23 2009, 06:19 AM
#4
which chip u r using.....how u interface pic and pc serially and what data u want to transfer from pic to pc
Mon Mar 23 2009, 08:36 AM
#5
You can refer to my experiment document attached to get a clear understanding. I'm using PIC16F877A. My main problem is to connect PC and PIC with RF module.
Mon Mar 23 2009, 08:37 AM
#6
I did the interfacing via USART using MAX232 level converter.


[ Edited Mon Mar 23 2009, 08:41 AM ]
Mon Mar 23 2009, 11:08 AM
#7
Hi Zacky,

can you provide circuit of controller's connection with TX and max connection with RX.

make sure you keep them some distance apart. dont keep them closer coz that will create more noise.
Mon Mar 23 2009, 11:12 AM
#8
Additional Q: I attached an LED to between the output of RF receiver and Gnd. I noticed the LED was constantly blinking although the transmitter is OFF. Also the blinking rate varied with different values of caps which is connected between the supply rail (i.e: +5V and GND). Does the caps plays a major role is this problem?
Mon Mar 23 2009, 11:14 AM
#9
Hie Ajay, thanx for the tips. I mounted them on a separate breadboard. Its separated about 30cm. Is it sufficient? Here's the connection diagram.

Mon Mar 23 2009, 11:15 AM
#10
I followed the guide on MikroBasic Manual for the diagram above.

Get Social

Information

Powered by e107 Forum System

Conversation

Sun May 20 2018, 10:01 AM
justinb
how to write and execute a program that read the keypad button and display the number on 7 segment on intel8051 at89s52 in assembly language?
Thu May 17 2018, 06:36 AM
HAMZA TAJ
sir iwant to ask about controller of three phase supply by using back to back thyristor instead of triac....will u give me some guideline?
Sat Apr 28 2018, 12:54 PM
ashutosh jain
IR Remote Switch using TV remote (RC5 Protocol) is not working properly. opp1 & opp2 is in problem.plz help
ExperimenterUK
Fri Apr 27 2018, 08:09 PM
@kaiserslautern Post in forum
Wed Apr 25 2018, 07:09 AM
kaiserslautern
Hello everyone, using software uart is a very good idea for a second serial port. Thank you so much. I would kindly like to know how to connect this port to the PC?
ExperimenterUK
Sat Apr 21 2018, 07:50 PM
This is a community site. Feel free to help anyone needing advice
hareeshchamiyar
Thu Mar 29 2018, 10:47 AM
please help me for the configuration bits for dspic30f2010
hareeshchamiyar
Thu Mar 29 2018, 10:45 AM
can any one using dspic30f2010.
Thu Mar 29 2018, 06:03 AM
Neena
can anybody give solar tracking in 8051 using proteus and keil to mail [email protected]
ExperimenterUK
Mon Mar 19 2018, 07:33 PM
sorry bedo.. maybe next time

Downloads

Comments

bdmehta
Tue May 22 2018, 02:30 AM
kmag1953
Sun Apr 29 2018, 07:09 PM
udiwonder
Sat Apr 28 2018, 12:41 PM
pirpiri
Sat Apr 21 2018, 03:35 PM
Pater
Fri Apr 20 2018, 02:38 PM
jamiel
Sat Apr 14 2018, 12:47 AM
akrepkral76
Wed Apr 04 2018, 07:51 PM
samanthaeaves
Mon Apr 02 2018, 06:27 AM

Online

Guests: 58, Members: 0 ...

most ever online: 182184
(Members: , Guests: 182184) on 06 Aug 2010: 05:37 AM

Members: 37998
Newest member: bdmehta
Forum Activity
ExperimenterUK Avatar
Posted By ExperimenterUK
Thu Jun 21 2018, 10:49 PM
The frequency of the pulses has to be the same as ...
LAMBO Avatar
Posted By LAMBO
Thu Jun 21 2018, 02:13 PM
hi sircan we change the frequency on pin no 39 of ...
ExperimenterUK Avatar
Posted By ExperimenterUK
Sat Jun 16 2018, 11:33 PM
hi sir sorry for the late reply sir can we control...
LAMBO Avatar
Posted By LAMBO
Sat Jun 16 2018, 07:15 AM
hi sir sorry for the late reply sir can we control...
ExperimenterUK Avatar
Posted By ExperimenterUK
Mon May 14 2018, 10:17 PM
So the main problem is that I am not getting Analo...
ExperimenterUK Avatar
Posted By ExperimenterUK
Mon May 14 2018, 09:40 PM
Hi sir after checking all the connection i...
Pater Avatar
Posted By Pater
Mon May 14 2018, 05:36 PM
Basically my project is based on Data Acquisition ...
LAMBO Avatar
Posted By LAMBO
Sun May 13 2018, 02:13 PM
Hi sir after checking all the connection i...
ExperimenterUK Avatar
Posted By ExperimenterUK
Mon May 07 2018, 07:27 PM
This design should be fine.Choose a frequency betw...
Pater Avatar
Posted By Pater
Mon May 07 2018, 01:28 PM
Sorry for late reply as exams were on,Based on my ...